I know there is another thread about resurrecting an Emag but I wasn't sure if protocol would approve of me hijacking that thread so I started this one to see if I could get a few quick questions answered as I've got a few parts I need to replace.
First, I need to replace the battery. My Emag was sitting in storage for quite some time and when I opened the battery case I found a nice pile of battery goo inside. I've cleaned it all out and have everything except the battery pack. I have the o-ring for the bottom of the battery case and I have the plastic top part with the connections. All I need is the battery with wire leads to solder to the connections.
I found the battery listed on the AGD store site here but it is out of stock. I also found a thread started by user "KC" here but it seems this user has not been online for a few months.
So, any other suggestions where I might track down a battery for my Emag? The wrapper lists it as a 16.8v 650mAH pack.
The next item I need is a bolt spring. My valve has "Emag" engraved in the side which leads me to believe it is not the Lvl 10 bolt. Measuring the bolt spring I have a length around 46mm and an outer diameter of 20.86mm.
Looking at the online store I found this spring listed under the Vavle and Valve Parts > 68Automag/Classic/ Minimag/Sydarm/Micromag Valve Parts section. I did not find any bolt springs listed under the Valves and Vale Parts > X-Valve/Retro/Emag/RT Valve Parts section. Is this the correct spring to use? I'm fiarly certain it is but would just like to double check with the experts here first.
The next item I need is the bumper found at the rear of the bolt itself. I found both this and this. Are either acceptable?
Last, I need a new barrel. My old barrel is held in place by a 1/4 turn or so and not threads. Went by my local paintball store today and they don't have any barrels like that anymore. Any recommendation of either where I can get a barrels which fits or switch my emag over to threaded would be greatly appreciated.
One last question actually. Since the gun has been without power for so long will I have to reload any software to the gun and if so where would I get it?
Thanks very much for the help.
First, I need to replace the battery. My Emag was sitting in storage for quite some time and when I opened the battery case I found a nice pile of battery goo inside. I've cleaned it all out and have everything except the battery pack. I have the o-ring for the bottom of the battery case and I have the plastic top part with the connections. All I need is the battery with wire leads to solder to the connections.
I found the battery listed on the AGD store site here but it is out of stock. I also found a thread started by user "KC" here but it seems this user has not been online for a few months.
So, any other suggestions where I might track down a battery for my Emag? The wrapper lists it as a 16.8v 650mAH pack.
The next item I need is a bolt spring. My valve has "Emag" engraved in the side which leads me to believe it is not the Lvl 10 bolt. Measuring the bolt spring I have a length around 46mm and an outer diameter of 20.86mm.
Looking at the online store I found this spring listed under the Vavle and Valve Parts > 68Automag/Classic/ Minimag/Sydarm/Micromag Valve Parts section. I did not find any bolt springs listed under the Valves and Vale Parts > X-Valve/Retro/Emag/RT Valve Parts section. Is this the correct spring to use? I'm fiarly certain it is but would just like to double check with the experts here first.
The next item I need is the bumper found at the rear of the bolt itself. I found both this and this. Are either acceptable?
Last, I need a new barrel. My old barrel is held in place by a 1/4 turn or so and not threads. Went by my local paintball store today and they don't have any barrels like that anymore. Any recommendation of either where I can get a barrels which fits or switch my emag over to threaded would be greatly appreciated.
One last question actually. Since the gun has been without power for so long will I have to reload any software to the gun and if so where would I get it?
Thanks very much for the help.
Comment