I need some advice please. SHP regs

[brassmag]

Im looking to buy a SHP regulator 4500psi for my mag xvalve.

What I want is a very easily adjustable (on the fly without taking it apart With shims) 1100psi 4500 reg

I know of two SHP regs.

I do NOT want the Ninja SHP because it uses shims to regulate and I do not like that.

I do not want the flatline because I have many guns and I dont want to get rid of my ASAs and find wever rails to mount the tank.

I do like the flatline very much but its too bad it doesn't screw into an asa...

What are other Super High Pressure regs?
I want to find one with an external adjustable output.

Thank you all

[OPBN]

Im not aware of any externally adjustable tank regulators that screw into an ASA.

[BTAutoMag]

Im not aware of any externally adjustable tank regulators that screw into an ASA.

ditto

have been looking

[brassmag]

Well if we figure this out then we will all be better off.

A list of all known SHP regs ever available would be a good start to finding the dream reg.


Lets get some info.
Thank you all

[BTAutoMag]

Well if we figure this out then we will all be better off.

A list of all known SHP regs ever available would be a good start to finding the dream reg.


Lets get some info.
Thank you all

more specific. We can all pitch in a collectivly come up with a list of every regulator that can break the 1000 psi mark.

and then sticky it!

[brassmag]

To start

SHP regs

AGD Flatline 3000psi and 4500psi
Ninja SHP 4500psi
.
.
.
.
What else

[Mole1119]

This is a good resource for information on this topic. I dont belive any of them are screw in.

http://www.zakvetter.com/pages/paintballs/automag_info/rapidfire/goodregs.html

The Ninja reg is the only one that I am aware of since the publishing of that page.

[Frizzle Fry]

To start

SHP regs
Ninja SHP 4500psi
Immortal Air Aura
Guerilla Air Myth G3
.
.
.
What else

Those ares some screw-in "adjustable" regulators capable of going over 1000psi reliably, though I like to think of them as "customizable" rather than "adjustable", seeing as you need to empty your tank and disassemble your regulator to change the output pressure. If you want the highest possible output and the easiest output adjustment, get a direct-mount regulator by AGD, Air America or Centerflag.

[BTAutoMag]

Luke or xmt needs to make a screw in adjustable

[Patron God of Pirates]

Im not aware of any externally adjustable tank regulators that screw into an ASA.

The old Nitro Duck adjustable's did. I ran one for a few years, but it would not crack 850.

[OPBN]

The old Nitro Duck adjustable's did. I ran one for a few years, but it would not crack 850.

I stand corrected. However, if they won't adjust past 850, not much use in this discussion.

With that said, I did search the Nitro Duck and came across a thread where it mentioned Rehvac as the company that made these for ND. Seems like I remember them continuing to make them for some time after and I could have sworn they offered some that were adjustable past 850. Maybe I'm remembering incorrectly....

[Justus]

You can add in the NitroDuck iReg, which is adjustable to hit 1000 psi, but not externally.

Again, I'm also not aware of any screw-in tank regulator that is externally adjustable up to or over 1000 psi output. I also have serious doubts that Luke or XMT would even want to tackle such a project, what with all the liability involved.


A question, however, is why you would need a screw-in type regulator to be externally adjustable? Don't like the RONCO way of doing things? (Set it, and forget it!)

[OPBN]

You can add in the NitroDuck iReg, which is adjustable to hit 1000 psi, but not externally.

Again, I'm also not aware of any screw-in tank regulator that is externally adjustable up to or over 1000 psi output. I also have serious doubts that Luke or XMT would even want to tackle such a project, what with all the liability involved.


A question, however, is why you would need a screw-in type regulator to be externally adjustable? Don't like the RONCO way of doing things? (Set it, and forget it!)

Based on his previous thread, he wants to control his RTing via output pressure.

[Nobody]

find a nice used Armageddon and that's it.

[Chencho]

max-flow? i have one and its awesome. adjusting its easy and on the go if necessary.