mag wizards needed

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Spook
    Registered User
    • Dec 2013
    • 89
    #1

    mag wizards needed

    Please can you help me with my rt pro valve it is leaking air like there is no tomorrow i have oiled it up and tried to cycle it but nothing happens i have adjusted the trigger still nothing i can put my finger in front of the bolt and it doesn't move if i push the bolt in ever so slightly the leak stops and the same if i pull the trigger in i have i have had a look in the valve and i have noticed that the spacer between the two o rings on the valve pin is split could this be causing the problem any help will be very appreciated
    Thanks
    Luke
    Tags: None
    • OPBN
      OldPBNoob

      • Sep 2008
      • 5240
      #2
      Sounds like you need to go down a carrier or two on your L10. Also, have you gone through the valve to insure everything is where it is supposed to be? Has it worked before and stopped working? Where is the leak coming from? Need more info.
      My AO Feedback

        Comment

        • Spook
          Registered User
          • Dec 2013
          • 89
          #3
          It is leaking from the power tube as far as i can tell and everything seems to be present and correct also it has a level 7 bolt
          I could not tell you if it was working before as i purchased it on here as working was told it was aired up and was fine i managed to get some air and found out it was leaking
          Last edited by Spook; 04-13-2015, 02:11 PM. Reason: missed a bit out

            Comment

            • OPBN
              OldPBNoob

              • Sep 2008
              • 5240
              #4
              Bolt spring may be worn. Might have to drop a spacer size.
              My AO Feedback

                Comment

                • Spook
                  Registered User
                  • Dec 2013
                  • 89
                  #5
                  It's a new bolt spring installed i will get some spacers and spares kit seems to be the best way forward

                    Comment

                    • Cyco-Dude
                      #6
                      Originally posted by Spook View Post
                      Please can you help me with my rt pro valve it is leaking air like there is no tomorrow i have oiled it up and tried to cycle it but nothing happens i have adjusted the trigger still nothing i can put my finger in front of the bolt and it doesn't move if i push the bolt in ever so slightly the leak stops and the same if i pull the trigger in i have i have had a look in the valve and i have noticed that the spacer between the two o rings on the valve pin is split could this be causing the problem any help will be very appreciated
                      Thanks
                      Luke
                      the spacer is supposed to be split, yes. if the leak stops when you hold the trigger, then you just need a new power tube o-ring most likely.

                        Comment

                        • Laku
                          Registered User

                          • Nov 2012
                          • 940
                          #7
                          Could be worn sear as well.

                            Comment

                            • Beemer
                              I could tell you but then.

                              • Oct 2003
                              • 3250
                              #8
                              Originally posted by Spook View Post
                              I could not tell you if it was working before as i purchased it on here as working was told it was aired up and was fine i managed to get some air and found out it was leaking
                              Who did you buy it from??

                                Comment

                                • Spook
                                  Registered User
                                  • Dec 2013
                                  • 89
                                  #9
                                  Originally posted by Beemer View Post
                                  Who did you buy it from??
                                  I bought it from captain pinky

                                    Comment

                                    • athomas
                                      Of course it works-its AGD
                                      • Jan 2002
                                      • 8039
                                      #10
                                      As the sear wears, you will need to install a shorter powertube spacer to compensate.
                                      Except for the Automag in front, its usually the man behind the equipment that counts.

                                        Comment

                                        Previous template Next
                                        Working...