Got a warp(AGD) a couple of months ago. Used it fine on my powerfeed TKO mag for a couple of games. Just got a Z-grip and a CP flame drop with on/off ASA. Hook everything up and for some reason my Warp won't spin when i fire. It's not even reacting to the recoil. I turned the sensitivity all the way up, and when placing the covering plate back on it did spin from that vibration, but it won't when I fire. I'm not sure what's wrong with it. I have the jumpers on factory setting, never changed those. Any help would be greatly appreciated.
-
"Conquest is made in the ashes of ones enemies." -Starscream -
My guess is that with the Z it's not getting enough Vibration.
Make sure that all the screws are tight, on the warp bracket and the drop forward.
You might want to consider intellifeeding, but you'll have to modify your zgrip to do it.
-
Screws are definately down tight, I guess I could intellifeed but i'm afraid i'll screw something up and won't be able to do it. I'd much rather find a fix for this problem."Conquest is made in the ashes of ones enemies." -StarscreamComment
-
Bump, there has to be some way to fix this..."Conquest is made in the ashes of ones enemies." -StarscreamComment
-
And it works with the other grip?-Gig 'Em Ags!Comment
-
yes it did. I didn't have the same drop on it though or the Z-grip."Conquest is made in the ashes of ones enemies." -StarscreamComment
-
What kind of battery are you using, a cheapass one or a quality $4 beast? it requires the extra amps of a $4 beast.Once you have shot and eliminated someone, you have established your position towards them. In a sense, the next move is up to them...
See ya in the dead box!Comment
-
Energizer, brand new out of the package."Conquest is made in the ashes of ones enemies." -StarscreamComment
-
My MiniMag with Z-Grip never triggered reliably with the vib sensor. That's why I set it up for intellifeed. All you need is wire, the sub-mini lever switch w/o roller ball from Radio Shack, plug to fit the intellifeed jack on the Warp board and a way to drill a hole in the frame to run the wires through.
Here's a pic of magc68's setup and how he hooked up his intellifeed system. He wrapped the switch in electrical tape until it was thick enough to press fit in the frame. I used double stick tape on my setup.
Here's how I dropped the wires out of the frame and then into the Warp. I'm left handed, so it'd be on the opposite side of the frame for you. Just make sure if you drill the hole in the frame, you need to drill it away from the holes for the top screws that hold on the grips so you don't drill through that and mess up the threads.
Comment
-
Well I may just intellifeed it but i'd still rather not. I was messing with my warp today and it seems odd. It's not spinning even if I shake the warp body. It used to spin just from me setting it down on the table or something similiar. Maybe the sensors shot or something I'm not sure. It does spin though if you press in the white button underneath the plate which covers the electronics."Conquest is made in the ashes of ones enemies." -StarscreamComment
-
Ok, i think i'm just gonna intellifeed it. Probably my best bet. Just gotta be careful drilling. Thanks for the help BlackVCG."Conquest is made in the ashes of ones enemies." -StarscreamComment
-
Tap on the side of the warp with a coin. If it doesn't spin your should either change the battery or the sensitivity.Originally posted by RATM
It's not spinning even if I shake the warp body. It used to spin just from me setting it down on the table or something similiar.
Hey Hitech your starting to sound like me! - AGD
Hitech is the man.... :eek: - Blennidae
The only Hitech LubricantComment
-
Your vib sensor might have some dirt under it or has come loose so the springs aren't getting proper contact on it. Check that out and make sure you have the springs still in place under the board.Comment
Comment