Power Feed Plug Adjustment & new vs old

[RobAGD]

Here are some pics of the new plug vs the old style plug the differance should be quite clear.



Ok gete is how the adjustment shoud look on a new Power Feed Plug.



Now you are saying Hey I can't see that in my power feed body ! So how do you test you adjustment ??

You get a long wooden Spoon or Stick squeegie some paintballs.

Now take out your barrle and remove you hopper and elbow.

Place the squeege down the breach and place the end under the power feed entrance. place a few balls 3 or 4 in the feed tube, now press down on them with your finger and then allow the squeege/spoon to drop and allow the ball to pass into the main body. You are feeling for a pause or a hang up on the lower lip. If you do not have the proper over hang on the plug you will have some small feed problems. So adjuster you set screws in or out as needed.

Or you can just get a small mechnics mirror on a stick and cheat

-Robert

[Blaze16016]

How Can I get one of thoose new Feedplugs? I still have one of the old ones and I would like to get this new one.

[MikeCouves]

Yeah I am with him on that. Is AGD still giving them to people that own mags?

[DarkPhoenix]

All you have to do is call the AGD front office on Tuesday. I ma sure they will be more than happy to help you out. Remember to give them your Valve serial number.

[wyn1370]

when you call ask for free stickers. everybody loves free stickers.

[Kdog]

How much does the plug cost or is it a free upgrade?

[GoblinGreen]

mine doesn't look like that!

Conparing my powerfeed plug to those that ROBAGD posted pics.
where Rob has the parabolic plug between those points(the actual curve itself) I have a square piece of plastic which makes a square corner for the paintball to drop into the barrel.
hope that makes sense.
would that also decrease feeding? is it as good as the parobolic plug?

[T F]

Okay here we go....

In Atlantic City Tom Kaye gave me a parabolic plug and told me to check this sight out if I had any questions as to how to adjust it... I installed the plug and it is not quite long enough to look like the pic above. When I run my pinkie nail down the parablolic plug face I can still feel a bit of the body where a ball could theoretically catch.

What should I do now? DREMEL!!!!!?????

TF

[PowerFedMag]

so

I think I have a parabolic pf plug but I have a SP splashed plug and its got the flat spot. What exactly happens if I use my flat spot SP pf plug over my parabolic one?

[MagNumPI]

You might end up with balls that pause on the way in.. fix , get a intellifeed system.. or what have you. I have the old school plugs too , but i have yet to encounter this problem.

[vaypourus]

AGD sent me a parabolic plug (for free!!!) when I regestered my gun online. I haven't used it all that much but, in the past I did have some feeding problems. Those problems haven't returned (yet?).

[FatMan]

I don't get it

I'm sorry, I must be dumb or something, but that second picture in the first post doesn't look like anything I've ever seen before. It looks sort of like an elbow, but that can't be right. I don't understand what I'm looking at or what the spot marked on the figure is or how it helps me to understand how to adjust one these plugs correctly.

Maybe a diagram would be more help - or a verbal description of a proper fit. Maybe if you even just described what that picture is so I can understand it.

I added one of these things to my Mag a few weeks back and I've been having feed trouble ever since. Also, since the two screws are independent, there is more than a simple depth adjustment, you can sort of "rock" the thing up or down by adjusting one screw at a time. Not sure what or how that should work. Also, since there are only two screws, the thing seems to rock from side to side. Not sure if that hurts anything.

So, I was hoping to get the low-down on how these things are supposed to be adjusted, but I'm not getting it from what was posted here. Might be because I'm slow or old or something, but I'm hoping someone will clear it up for me.

Thanks in advance,

Fatman

[BlackVCG]

The second picture in Rob's post is of a 90 degree Warp Feed adapter. The picture basically shows that when the plug is in the position so that the balls can flow through, there should be a small bit of the plug overhanging the feed tube or in the case of the picture, the edge of the plastic. Here's a better pic of the unit in the second pic.



*Note: The PF adapter in my pic has the old PF plug in it. You want the PF plug with the hole in the handle and the two set screws in the handle.*

Adjustment of the PF plug is fairly simple but you need to make sure it's even and adjusted properly. Proper adjustment is like what's shown in the second pic of Rob's post. It's not THAT precise of a piece that the side to side movement doesn't make any difference.

[FatMan]

Thanks

Wow, that cleared up a lot! I understand now. And you say don't worry about the side-to-side stuff.

Cool. Thanks!

FatMan

[freek133]

how about

if i just bought a minimag will the new feedplugs be on there?