Oh yes it does :-) Took me a while to get it hooked up, but it works very nicely.
It's actually got significantly better logic than the standard board because with the stock board if there is no ball it won't fire at all (or start a warp if a ball is missing...) With the Morlock it will still fire after a short hold off and this means it will clear any problems with badly fed or shaped paint and start a warp etc. to feed if there had been a misfeed for some reason (for instance running out of paint).
With a bad ball in the stock gun with level ten, the bolt may push it forward off the ACE but not fire it. Resulting in not being able to shoot. With the Morlock it will default so you can start shooting and off you go again after that ball is pushed a bit further forward and fired under a 'forced' shot :)
OK So I am just wondering what settings others are using? Any one using a Tunamagnum/Morlock or E-magnum please post up your settings. Maybe we can work out the optimal set up, with and without the ACE.
What did Butterfingers use to get 30bps?
1) Fire Mode = semi
2) N/A
3) Solenoid one pulse length = 15ms (interested to know what others use)
4) Solenoid one hold off = 1ms (wondering if I ought to set this high enough to allow recharge or just set it as low as possible?)
5) N/A
6) ROF/Solenoid 2 hold off = 1ms (am using ACE)
7) Eye Hold off = factory default is it 10ms or 5ms? there seems to be contradictory statements in the instructions. (seems fine with a Halo B) may be a little short with a normal loader, but I had no chops on FA and only one/two breaks at the very tip of the barrel... also very fragile paint!) Am wondering if I can go to no hold off... I want to squeeze every ounce of fire power out of this thing!
8) Use Eye = YES!!! :)
9) Solenoid mode = single solenoid
10) Lock mode = semi
11) Eye sense = low blocked
It's one heck of a machine gun set up like this. Especially on FA, where it will spit out a line of paint faster than my Halo B can keep up :) It won't actually fire properly without the ACE on FA as it seems the settings are currently too quick for it to just dry fire
manike
It's actually got significantly better logic than the standard board because with the stock board if there is no ball it won't fire at all (or start a warp if a ball is missing...) With the Morlock it will still fire after a short hold off and this means it will clear any problems with badly fed or shaped paint and start a warp etc. to feed if there had been a misfeed for some reason (for instance running out of paint).
With a bad ball in the stock gun with level ten, the bolt may push it forward off the ACE but not fire it. Resulting in not being able to shoot. With the Morlock it will default so you can start shooting and off you go again after that ball is pushed a bit further forward and fired under a 'forced' shot :)
OK So I am just wondering what settings others are using? Any one using a Tunamagnum/Morlock or E-magnum please post up your settings. Maybe we can work out the optimal set up, with and without the ACE.
What did Butterfingers use to get 30bps?
1) Fire Mode = semi
2) N/A
3) Solenoid one pulse length = 15ms (interested to know what others use)
4) Solenoid one hold off = 1ms (wondering if I ought to set this high enough to allow recharge or just set it as low as possible?)
5) N/A
6) ROF/Solenoid 2 hold off = 1ms (am using ACE)
7) Eye Hold off = factory default is it 10ms or 5ms? there seems to be contradictory statements in the instructions. (seems fine with a Halo B) may be a little short with a normal loader, but I had no chops on FA and only one/two breaks at the very tip of the barrel... also very fragile paint!) Am wondering if I can go to no hold off... I want to squeeze every ounce of fire power out of this thing!
8) Use Eye = YES!!! :)
9) Solenoid mode = single solenoid
10) Lock mode = semi
11) Eye sense = low blocked
It's one heck of a machine gun set up like this. Especially on FA, where it will spit out a line of paint faster than my Halo B can keep up :) It won't actually fire properly without the ACE on FA as it seems the settings are currently too quick for it to just dry fire
manike
Comment