ANS Automag valve kit

[mr_cool2588]

I was given the ANS automag valve kit(Oh the incentives of refing at paintball fields). Any way, the kit includes the true flow valve, the venturi bolt, and the phase II air valve. The bolt installed fine, but should the rest of the products work with a semi old school RT(After highrise before pro). My serial # is RT03029, if they should work please let me know how to install them.

Thanks.

[Bulldog]

Honestly, you shouldn't even bother. Your better off with stock parts. See if you can sell it on ebay. That would be my suggestion. Pure profit, seeing as how you paid nothing for it.

[Miscue]

Sell it, don't put it into your gun. Use that money for a Level 10 Kit if you don't have it.

[rikkter]

why would you take the RT part out? i'm sure ANS doesn't claim it recharges it to 26 BPS (then again if they do we know its BS) like the one that you have on it now does

[DeathscytheSK]

yeah defiently keep the RT in there, it will kick the ANS Valve's rear end, you won't regret it and Miscue is right, defiently sell it for a Lvl 10, best combo for a Mag

[rikkter]

Originally posted by DeathscytheSK
yeah defiently keep the RT in there, it will kick the ANS Valve's rear end, you won't regret it and Miscue is right, defiently sell it for a Lvl 10, best combo for a Mag

..only if you have a severe case of chopping. if you dont, why bother with the less air effeicenty.. and well yeah you get less recoil, but still!

[Paintmanmike]

I do not know about the RT but hte ANS Phase II works very well in my Mag. No shootdown and pretty tight velocity, and grouping too

[rikkter]

now compare it to the original reg half. i bet you theres no difference IF any

[paint magnet]

Waste of money. ANS regs suck, venturi bolts also suck, and so does ans ever made.

[athomas]

Does the ANS valve kit even fit on an RT? The ANS was designed to increase flow in the original AGD AIR valves which had flow problems due to air ports that were not properly lined up during manufacturing (it wasn't as much of an issue back then). Its not a problem anymore so these ANS products now fall into the hype category.

Sell it and get something usefull like a level 10 bolt.

[rikkter]

i'm assuming they do since theres no thread difference and length in the rt and air valve are there?

[Paintmanmike]

rikkter,

There may be no difference, it came with my Mag when I bought it used and its given me no reason to dump on it. If I get a stock one someday I'll be in a position to run that test.

The best reason to not get any aftermarket valve is that AGD will not work on your marker unless its got a stock one. That has not been a problem for me at all, I'm pretty good at upkeep and repair myself, but it is something to keep in mind. I hope it never becomes an issue.

[toymyster]

No, they will Not work with the RT!!! Those parts are for the for the classic valve only!!! The fact that they don't work set aside!!! Also, you will find that the ANS bolt will wear rather quickly, personal experience: stick with the original AGD parts!! If you want a bolt upgrade, invest in the Level 10!!

[Hexis]

Do the world a favor and thorw those parts away. Selling them to somone else just puts the problem on somone else. They will come here asking how to make them work and we will tell them to throw them away or sell them again. What an awful cycle.

[paint magnet]

Hey, if you really want a better (if you can get better than AGD) reg on your mag, get one of those Palmer's stabilizers that screws right into the side of your regulator, that will give you a dual regged setup and PPS quality.