Hyperframe FAQ

[hitech]

[olinar]

alright i need some help.ive got a hyperframe and it works perfect.i know this because i took it all apart and i pushed a hex key against the solenoid and i fired and it released the solenoid and i can adjust everything from rof to shot count.only thing though is it onw fire my gun.my valve works perfect the sear is perfect ,im sure i just have to adjust the dwell.in the manual it says i can do that in service mode.how do i get itno service mode?also its not really a big deal but my lcd screen tends to only work on the bottom half of it.it usually goes back to normal with a few taps but if there is a way to fix that as well i would love to know.thx and sorry for the long post.

[11 Bravo]

The manual should tell you how to get into service mode. If I remember right - you hold down both buttons at the same time. This should get you into service mode.

[Tombola]

[nevtangle]

Try posting in the BST section that you want to buy a trigger pin for the HF.

[11 Bravo]

Try emailing Center Flag and see if they have any left. [email protected]

[smilestyler]

Can't let this thread die. It's full of too much valuable info.

[redmagik]

Troubles

So I have a hyperframe, 13bps type. It cycles, no problem there. LThe problem i have is getting it to shoot on any of my mags. I have air valve, classic valve, retro, emag, and xvalves. It will trip the sear sometimes but not consistently...forget full auto. I have a level 10 bolt on the emag vavle and the xvalve with a ult kit. Any ideas?

[hitech]

You need the centerflag on/off, or a ULT. Anything else and results are iffy. If you have a level 10 bolt in that thing even the centerflag on/off is iffy.

[redmagik]

on/off

So...if i use the e or x valve with level 10...not a good idea. If I use the classic vavle I should try to hunt down a centerflag on/off? Wow...any ideas where to get that?

[hitech]

So...if i use the e or x valve with level 10...not a good idea. If I use the classic vavle I should try to hunt down a centerflag on/off? Wow...any ideas where to get that?

A classic valve with the standard on/off will NOT work. Period. You would have to replace the on/off with the centerflag on/off (no idea if you can get one, try calling Centerflag) OR a ULT.

The e or X valve will also require either the centerflag on/off OR a ULT, although rumor has it that with a level 7 bolt the RT style on/off does sometimes work.

In either valve, you MAY be able to get it to work with a centerflag on/off and a level 10 bolt. The shortest spring from the level 10 kit is the only one that is likely to work. This is regardless of the valve (e, X or classic).

A ULT has a much higher chance of working with a level 10 bolt. I've never heard of one not working, but...

[redmagik]

tHANKS

Thanks HiTec for all the info. I love these forums

[redmagik]

Got it Working

Sweet! got my hyperframe working. Has anyone tried a virtue board in a hyperframe? Or is the T-Board the best way to go?

[hitech]

Glad to hear it works now.

I don't know enough about either board, but either board will require a custom installation, it won't be a drop in swap. In either case, you need to have that large cap that is on the top of the hyperframe board. It is basically required to be able to power the solenoid with a 9 volt battery.

[p8ntbal4me]

Sweet! got my hyperframe working. Has anyone tried a virtue board in a hyperframe? Or is the T-Board the best way to go?

Search this forum for a post done by someone that bought a SD board and used it in a Hyperframe.

The user that did it reported a COMPLETE drop in replacement.

Cant get much better than that.

~ P8nt