Hyper Frame BPS help??? NEED TO KNOW ASAP!!!

[nato]

The xvalve works fine now... I entered the following numbers int the centerflag hyperframs:
15 - 20
Fd - 50
Fn - 20

Once I did that I installed the hyperframe again and it leaked a lot of air down the barrel. The only way to stop it was to hold the bolt back.

I assumed that the reason why its leaking is because of the new settings in the hyperframe.

What I dont know is how to adjust the hyperframe correctly to keep it from leaking now.

LMK and thanks for the help so far, I appreciate it
N.A.T.O.

[hitech]

Okay, the leak has nothing to do with the dwell settings. The most likely problem is the solenoid is not allowing the sear to latch completly. Read my FAQ to find out haw to adjust the solenoid. You need to make sure the sear is latching all the way.

[nato]

The only part that talks about this is titled

"Adjusting the Hyperframe's solenoid, On/Off pin to short"

Even if I have ULT I can have a bad length for my on/off pin?

N.A.T.O.

[nato]

Also, why did this just suddenly pop up when it wansn't happening before?

N.A.T.O.

[hitech]

Originally posted by nato
The only part that talks about this is titled

"Adjusting the Hyperframe's solenoid, On/Off pin to short"

Even if I have ULT I can have a bad length for my on/off pin?

N.A.T.O.

No, the on/off pin is fine. However, the solenoid has a VERY SMALL throw. If could be blocking the leg sear from moving forward.

Sorry, but it's hard to be sure without being able to see what is happening.

[nato]

well Im starting to take the saftey off right now but just to make sure it was still leaking, I aired the sucker up one more time and the gun shot once (without touching the trigger) then was quite. I pulled the trigger and it would fire (still at low speeds). After firing about 900 psi away on my tank the guns lvl 10 started to make a short stroke sound and then just stopped firing but I could still hear my solenoid tapping away against whatever it was. So I am pretty sure that you are right due to the fact that the marker still responds to trigger pulls, just not always shoots. Ill mess around with it tonight and I hope I can do some good which I unfortunatly doubt.

N.A.T.O.

[nato]

Ok, so I messed with the frame and MAY have fixed it... its firing well now and hopefully good to go. At 1st I brought the brass cylinder... noid? (pardon my newb language)all the way back to the lfet of the frame and the marker did not respond kindly... I brought it closer to the right but still more left than how it was in the 1st place and it seemed to work out. Im attatching a pic to show what I did to make sure I didnt just "ruin" the frame forever.

The one other problem that I STILL must address is the BPS issue. It has not changed at all and is really starting to piss me off due to the fact that I can fire faster with my intel. frame.

LMK.

N.A.T.O.

[spantol]

Have you tried the heavier switch yet?

[nato]

no I have not... why do you think the bps has to do with the switch? It seems that when I walk the trigger with the lighter switch, the screen responds to speeds faster than it is currently doing. I just dont know why it will not fire as fast as it responds to my fingers.

N.A.T.O.

edit: now that I think about it, I think the board may actually be responding to each trigger pull but the solenoid (doowacky (brass thingy)) Is for some reason too slow to react to the trigger pull. As I said before, I noticed that it was sometimes sluggish and would not open and close all the way when I fired... could this be the bps problem?

[hitech]

I am currently out of town, with limited access. I will try to look at the picture later and comment.

[Digits]

thats what mine does to.. It only fires like once every 2 pulls.. It seems like it's capped at like 8.. When it says 13.. I have the new board coming.. But.. Hmm.. Maybe try loobing the solenoid.. So that it runs smoother? You never know

[hitech]

[nato]

My newbish words and "skills" bother me... I must adjust this thing called the hyperframe and I'll let you know what happens... although I think I already fixed the firing part right due to the fact that it fires great now with and without paint... just bps trouble now.

N.A.T.O.

[nato]

[hitech]