Ok after reading a thread about power tube spacers I decided to take my gun apart to see if I have a power tube spacer or a spring (I bought it used so I don't know) cause I have been having bolt stick ( I think thats what it is) and my trigger get sticky (could that be from bolt stick?). But when I went to remove the little brass piece I couldn't get it off. Instead the whole power tube came off and all I could see was a big empty chamber. How do I get the brass piece off?
-
Go tell your mom.
Green Poop -
Call AGD you will need to send it in to have the powertube put back on properly.
How old is your gun?
-
What do you mean have the powertube put back on properly? I don't know how old my gun is. I bought it used. And whoever I bought it from voided the waranty. My gun is 1/2 classic 1/2 Mini.
How much do you think it will cost for a full check up? Will they replace the power tube? It has some deep scratches in it.
Go tell your mom.
Green PoopComment
-
Defiantly call AGD. Put it all in a box and send it to them. Call first and get an RA#. You will need to write that on the outside of the box. Request a copy of the Automag video while you are at it. This may be a little old, but it will show you all you need to know as an owner of an automag.
The gun is 1/8" of a game that is a FOOT long!
(...but a 'mag helps)
I know I was born and I know that I'll die...the in between is mine. -Eddie Vedder
Sinister SainthoodComment
-
I will send it in ASAP. I will have to wait a while though. I just bought an E-LCD off of ebay and the guy forgot to send the E-LCD on/off valve, so I have to wait for that. I alread tryed using the stock valve and it doesn't work. It just vents air like crazy. Is that cause the pin is too long?Go tell your mom.
Green PoopComment
-
Vents air from where? Out the back? front?
The gun is 1/8" of a game that is a FOOT long!
(...but a 'mag helps)
I know I was born and I know that I'll die...the in between is mine. -Eddie Vedder
Sinister SainthoodComment
-
I think it was venting out the front. This happened *** soon as I gassed it up and untill I took off the tank. I am assuming this is because the stock on/off pin is too long and was being pushed in right as the air was applied and it just stayed open. Thats probably why Boo-Yaah gives you thier on/off, but i'm just guessing.Go tell your mom.
Green PoopComment
-
um...i didn't mean to swear in the above post. Typo. Sorry.Go tell your mom.
Green PoopComment
-
Sounds like a wrong sized power tube spacer. Call AGD.
The gun is 1/8" of a game that is a FOOT long!
(...but a 'mag helps)
I know I was born and I know that I'll die...the in between is mine. -Eddie Vedder
Sinister SainthoodComment
-
Well it didn't do that till I put on the E-LCD. I will call AGD though.Go tell your mom.
Green PoopComment
-
The wrong sized PT spacer isn't going to cause the PT to come off...Originally posted by Doobie
Sounds like a wrong sized power tube spacer. Call AGD.
And it probably won't cost you much if anything to have it put back on.Comment
-
PyRo: I meant the leaking down the barrel part.
The gun is 1/8" of a game that is a FOOT long!
(...but a 'mag helps)
I know I was born and I know that I'll die...the in between is mine. -Eddie Vedder
Sinister SainthoodComment
-
Well, I think the solution for that problem has already been established Id imagine that if he sent it in to have his PT replaced, they would fix his barrel leak at the same time
Comment
Comment