Adding everything I can to my Gold PTP MicroEMag, Advice needed

[Stimulation]

I am ready to throw a good three or four hundred bucks into my PTP MicroEmag. It is golden. I bought it for $700, here:

http://www.automags.org/forums/showthread.php?t=141181

Here is a pic of my gun:



I have already purchased this 45/45 Kiss Angel Air, and WarpFeed is my next step.

Here is the angel air:



I am going to be doing the 12V warp mod along with the on/off switch with LED. I am going to purchase an 89.00 blue warpfeed from agd.

I assume I also will need to purchase PTP's warp feed adapter:



Does this gun have an intellifeed in the frame? If it does, what will I need to do in order to connect it to the warp and all? If not, what will I need to do to have the warp fire every shot? I am sure I could rig something up.

In addition to that what else do you suggest I need Warp-wise?

Now, to my next question. The gun seems to be older (only has 1.37 software) and has an older/rarer valve, it says emag micro 2000 on it. Does this have LVL 10? It says so in the ad, but i just wanted to check. The rubber insert does seem to be gone/ removed from the bolt. Would there be any sense in upgrading the valve system. I probably will be sending it in to AGD to get the software upgraded, along with a trigger job. Should I valve them mess with the valving at all?

Other than that, what else can I upgrade? The barrel is nice, an armson rifled, yet it couldnt hurt to have a kit. I have had a mag and warp before (done the 12v mod as well), and wanted to purchase another, and stole this beauty for $700, 300 less than I dedicated to a new mag. So, I get to upgrade. Thanks for you guy's excellent advice, I appreciate it. I hope I have been an detailed as possible.

- Stim

[Dayspring]

Doubtful that it has level 10.

Pull the bolt out. If it's got a thin piston, it's a level 10. If it's thick, it's level 7.

Your valve is no different than any other valve out there now.

AGD can upgrade your software easily, but I point you towards www.havoc-online.com for instructions on trigger jobs. It's subjective- as you may not like their trigger work.

I am ready to throw a good three or four hundred bucks into my PTP MicroEmag. It is golden. I bought it for $700, here:

http://www.automags.org/forums/showthread.php?t=141181

Here is a pic of my gun:



I have already purchased this 45/45 Kiss Angel Air, and WarpFeed is my next step.

Here is the angel air:



I am going to be doing the 12V warp mod along with the on/off switch with LED. I am going to purchase an 89.00 blue warpfeed from agd.

I assume I also will need to purchase PTP's warp feed adapter:



Does this gun have an intellifeed in the frame? If it does, what will I need to do in order to connect it to the warp and all? If not, what will I need to do to have the warp fire every shot? I am sure I could rig something up.

In addition to that what else do you suggest I need Warp-wise?

Now, to my next question. The gun seems to be older (only has 1.37 software) and has an older/rarer valve, it says emag micro 2000 on it. Does this have LVL 10? It says so in the ad, but i just wanted to check. The rubber insert does seem to be gone/ removed from the bolt. Would there be any sense in upgrading the valve system. I probably will be sending it in to AGD to get the software upgraded, along with a trigger job. Should I valve them mess with the valving at all?

Other than that, what else can I upgrade? The barrel is nice, an armson rifled, yet it couldnt hurt to have a kit. I have had a mag and warp before (done the 12v mod as well), and wanted to purchase another, and stole this beauty for $700, 300 less than I dedicated to a new mag. So, I get to upgrade. Thanks for you guy's excellent advice, I appreciate it. I hope I have been an detailed as possible.

- Stim

[pointm@n]

The warp will spin every time you pull the trigger out of the box because it's vibration activated. There is also an emag to warp harness that you can purchase. It plugs into the emag board and into the warp.

I'm not sure how that 45/45 Angel air unit will work on your MicroE. Emags like to have High Pressure systems. If that Angel air unit can't put out at least 700 PSI, then it'll be starving the emag. The emag may not even shoot. Also 45ci is pretty small. Emags are gas hogs and you'll be refilling that tank almost every game (depending on how much you shoot). I'd suggest at least a 68ci.

A barrel kit is always nice to have.

[Stimulation]

I also forgot one thing about the warp feed. Is it also possible to have the feed neck removed and put in a smaller, low profile feed neck that is threaded for the gun. I will still need the adapter, right? What size feed neck is the micro 2000 (autococker, mag?)? It would work the same but just be lower profile.

[Stimulation]

The angel air is completely adjustable, from 0-1200psi or something like that (It wasn't advertised as a low pressure version, so I doubt it is.)

I will be purchasing the AGD board to warp kit. Thanks.

Any other suggestions/comments?

[Person]

Id suggest not getting a warp because of your vert feed, but thats just me.

[Stimulation]

Nah, I had the warp before in 12V form, and love the speed and position of it. It will make this micro mag with 45 ci tank setup really tight!

[RTC_LoKi]

wow thats a beutiful gun

[personman]

Get a yellow haveblue display.. I think it would be a nice touch..

http://www.automags.org/forums/showthread.php?t=143015

[Stimulation]

Thanks for the complements guys, anybody else have any good ideas like the yellow lcd?

[Cthulhu]

A team mate picked up an e-mag that the previous owner had taken the valve and had it gold plated. Its a very light gold plating but looks damned sweet ntl... Didn't cost him much either. He did the teardown bolts too.

Nice E, I'd be afraid to take it on the field lest I get the glare off it and come off blind.

Cheers