4.0 software

[Flossabe]

Does any one know how to program or change the words that come up when you turn the gun on, or if it is posible to change at all?

[Tunaman]

not on the 4.0 no.

[eadtf]

O.k. what about 3.2?

And does anyone know if AGD is going to fix 4.0 and maybe reissue it as 4.1 or soemthing?

Pat

[Flossabe]

4.0 software

THanks Tuna, 4.0 and 4.01 are not a bad software it is more a hardware issue, i think it may be caused by the HES, one reason I think this is I have a friend that has a timmy with a magnetic actuatied trigger and he can bust out 29 by holding the trigger in the right place with no bounce the gun just goes full auto, I dont have this problem until my battery is 98% dead wich I would never play with it that dead any way, but I think it may be a HES noise issue, havent had a chance to check out more sensitive or diffrent HES sensors just what I think off hand.

[Cryer]

Since the emag has been discontinued, I doubt there will be any more software upgrades.

[eadtf]

cont...

As I recall talking to a AGD Tech, the reason that 4.0 was recalled was due to a safety issue?!?!? Not sure, but he said they my fix it and allow owners to send theres in for the udate. To the best of my knowledge there is nothing beyond 4.0 at this time.

Pat

[Vendetta]

I got 4.01 on mine with no problems. They'll have to pry it out of my cold dead board

[RTDynaflow]

Excuse my ignorance. What is the difference between all the diffferent e/x - mag software out there? I am looking at either buying an X-mag, 2k4 Timmy, Viking, or Custom Dallara Devilmag. (wish I could kidnap the hair from nicad ) Hoping some more info on the subject will sway me towards the X-mag.

My apologies for jacking this thread.

[Bad_Dog]

hmmm, I had 4.01 since I bought my Emag... Tuna recently flashed it down to 3.2...

I had full auto issues and neither me, or Tuna could get it working properly

[eadtf]

Want to make my own bios!

hmmm, I had 4.01 since I bought my Emag... Tuna recently flashed it down to 3.2...

I have seen this allot on the different forums.

Does anyone know what equipment you need and the programming language the bios is in? I would like to play around with making a custom bios, any help would greatly be appreciated!

Pat

[Miscue]

Since the emag has been discontinued, I doubt there will be any more software upgrades.

Yup.

[Miscue]

I have seen this allot on the different forums.

Does anyone know what equipment you need and the programming language the bios is in? I would like to play around with making a custom bios, any help would greatly be appreciated!

Pat

BIOS?

If you're serious, and you don't know how to do assembly or embedded systems programming - you'll need to learn that first before it can even be attempted. If you do, then I have to wonder why the question was asked in the first place.

[eadtf]

Title goes here!

Well rather than posting something that someone else could read and find useful you decided to post so rhetorical crap!

Good Moderation!!! Miscue


As stated before:
Does anyone know what equipment you need and the programming language the bios is in? I would like to play around with making a custom bios, any help would greatly be appreciated!

[Miscue]

Well rather than posting something that someone else could read and find useful you decided to post so rhetorical crap!

Good Moderation!!! Miscue


As stated before:
Does anyone know what equipment you need and the programming language the bios is in? I would like to play around with making a custom bios, any help would greatly be appreciated!

It's not a BIOS, it's a microcontroller.

My answer was not rhetorical crap. Your correct response was: I don't know how to do that, where do I start? or: I do know how to do that (Followed by good questions that someone who knows how to would ask).

This is what you need to know and understand:
http://www.atmel.com/dyn/resources/p...ts/DOC0839.PDF

Go through that, and you'll be on your way to writing your custom software.

[Miscue]

This is what you need to know to program the display:

http://cp.literature.agilent.com/litweb/pdf/5988-4161EN.pdf

This might be helpful as well:

http://www.egr.uh.edu/Courses/ECE/ECE5440/Project/Data%20sheets/Displays/5963-7071E.pdf

Enjoy.