E-mag bouncing

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Vash-HT
    Registered User
    • Sep 2004
    • 66

    #1

    E-mag bouncing

    Alright, Ive searched the other threads about this, and none of them really answered this, so here goes. I just got my emag last week, and i took it out to play in my first tourney this saturday. i noticed when i aired it up i could get double or more shots if i pulled it slowly. i tried adjusting the trigger, unfortunately my on/off pin was sheared in half somehow, so i couldnt really test it with air...

    so anyway, I have 1.37 software, and i was looking around, and i didnt really come to a clear answer my question, will 3.2 get rid of this bounce? plus, i tried screwing around with the trigger more when i got home, and i noticed i could get it to bounce without air, and it bounces no matter how heavy or long the pull is. Could this come from low battery?
    My Feedback
  • Couponqueen89
    AKA Couponqueen89
    • Jun 2003
    • 1571

    #2
    if you run it in E mode,you can take out the sear pin behind the trigger.
    Team Lockout Freeflow Racegun FST! Trust.
    AIR

    Comment

    • Vash-HT
      Registered User
      • Sep 2004
      • 66

      #3
      its not the trigger rod, i can do it without the air on even, so the trigger rod barely even moves.
      My Feedback

      Comment

      • athomas
        Of course it works-its AGD
        • Jan 2002
        • 8039

        #4
        The full auto phenominon is usually reserved for higher firmware revisions and can be corrected by reversing the solenoid wires. Yours being a lower firmware revision, maybe the HES has poor hysteresis. That means the on and off points are too close together. This can cause full auto.
        Except for the Automag in front, its usually the man behind the equipment that counts.

        Comment

        • chirogator
          Registered User
          • Apr 2004
          • 42

          #5
          hes wires

          hes wires might be backwards. Don't know where but there is a thread describing this phenomenon.
          I woudn't be caught dead with a necrophiliac!
          Gravity- It's not just a good idea, it's the LAW!
          :bounce:


          ULE Karta E-mag, X-valve, Morlock Board, Freak kit

          Angel Speed 05, Freak Kit, Nitro Duck X-Stream Tank

          Comment

          • Vash-HT
            Registered User
            • Sep 2004
            • 66

            #6
            athomas- so can this be fixed by lengthening the trigger pull, or is it through adjustment to the HES sensor?
            My Feedback

            Comment

            • athomas
              Of course it works-its AGD
              • Jan 2002
              • 8039

              #7
              If the problem is bad hysteresis, then the only fix is replacing the HES. Try all other avenues first though. Reverse the solenoid wires and/or adjust the trigger stop so it is farther forward(you will probably have to adjust the trigger magnet as well). Heck, even try reversing the trigger magnet. Uusally it won't activate at all when the trigger magnet is backwards, but it is worth a try.
              Except for the Automag in front, its usually the man behind the equipment that counts.

              Comment

              • dsrkd
                Registered User
                • Mar 2003
                • 994

                #8
                My suggestion is to send it to BlackVCG (on the west coast) or Tunaman (on the east). 3.2 is a world better for control. Black flashed one of my E's from 1.37 to 3.2. Worth it to me. Fires like a dream.

                Comment

                Working...