ANS Foamie Bolt

[DR@GON]

Hey all, Listen i have a new ANS Foamie bolt for my classic Mag.. Being new to Mags i need to know how the original bolt comes off?? Will it slide off and i slide new one in its place???? Any help is appreciated......

[LunchBox89]

yes it will slide on but why did you buy it its a waste of money and wont work as well (i think)

[DR@GON]

Really? I liked the idea of the foamie and the venturi config, Like i said im new to Mags so im gonna ask lots of ???'s I know this i like my Mag so much that my Custom 98 has become my back-up Marker!!.!.

[LunchBox89]

well you can get foamie on agd bolts aswell and ao quality is always in stock

[kevdupuis]

The venturi doesn't make a difference in the operation and yes all lvl 7&10 bolts are now foamies, though I prefer the old long nose bolt for lvl 7.

[LunchBox89]

thats the one i have

[DR@GON]

Ok how would i get a foamie for my lvl 7 at the agd store?? I thought they were for the Lvl X only????? If not ill order some right away..........

[kevdupuis]

Here http://store.airgun.com/index.cfm?fu...&categoryID=16 for relacement foamies. You need to make sure you scrap all of the old glue from the bolt face and use superglue to attach the new foamy.

You can get a new lvl 7 foamy bolt here http://store.airgun.com/index.cfm?fu...&categoryID=18 if you need one.

[DR@GON]

Cool Dude, Thanx for the links ill get right on that heh heh

[BlackVCG]

The ANS bolts were okay. What they did was decrease the efficiency of the gun by creating a restriction with all those small holes and they also wore out fast because they were not heat treated properly like the AGD bolts.

The result is a bolt that doesn't last long and you might need to change the PT spacer to get it to work.

Just order a Level 7 foamie bolt from AGD and use that. A word of advice though, if you plan on using Level 7, you should put a small radius on the tip of the bolt. It was discovered through AGD R&D that the sharp corner on the tip of the bolt was prefracturing the next ball in line and this was a major reason for all the ball breaks in Mags.

Use some 600 grit sandpaper and put a radius on the tip of the bolt all the way around so you can help reduce ball breaks.

[MindJob]

The ANS bolts were okay. What they did was decrease the efficiency of the gun by creating a restriction with all those small holes and they also wore out fast because they were not heat treated properly like the AGD bolts.

The result is a bolt that doesn't last long and you might need to change the PT spacer to get it to work.

Just order a Level 7 foamie bolt from AGD and use that. A word of advice though, if you plan on using Level 7, you should put a small radius on the tip of the bolt. It was discovered through AGD R&D that the sharp corner on the tip of the bolt was prefracturing the next ball in line and this was a major reason for all the ball breaks in Mags.

Use some 600 grit sandpaper and put a radius on the tip of the bolt all the way around so you can help reduce ball breaks.

Good advice.

I also had an ANS foamy bolt. I got it after I made the mistake of getting rid of my original AGD foamy bold when the foamyless ones came out. It is ok. The little foamy stayed on mine forever.

Best peice of advice it to plan on getting the LVL 10. Well worth the money and time you'll invest in it.

[mikeller1219]

i agree go lvl x soon as you get the money... stops ball breaks entirely and those stupid little foamies are gone forever

[DR@GON]

Cool guy's, Thanx for the advice and the info. I have been looking around the net and i have found a Lvl X for $69 so i think ill go that route........ MAG'S Rule!!