Help With This Dang Eblade

[CockmyCocker]

i need help with my dang eblade its all messed up it wont really shoot with eyes on the vol keeps going upand down its just fallin apart i need help when u go to shoot its like its not gettin air at all i have done all that i know how to do i think my blade settings are i need help

[P8NTBALLER590]

eye off.. get a halo if you dont have one. problem fixed.

[CockmyCocker]

iv got an egg thats fast enuffm and the only way it really shoots is with eyes off cuz with the eye on it has y to much blow back coming out but its just not shoot realy at all its like its not gettin any air

[chaos lichen]

Have you adjusted it to make it "better"; or did this problem just happen when the eblade was left to its own devices? If is the former change the settings to a factory speed. It also sounds as if you have your bolt upside down. (it sounds silly but it happens to the best of us)

[CockmyCocker]

yea iv messed with it and had the feild tech look at it its on a ultralite mini so the bolt cant be turned upside down

[CockmyCocker]

ok iv just thought of this just give me a im at skycam420 and ill just get ur settings off ur eblade so mine will work i will deeply grate full

[Flow_Tech]

put it back on factory fast with all of the bounce FILT on 2,and raise the CDEL to 4.then bring the CON down to 50 if you have a revvy,26 is what i use with a HALO/Egg2,then just raise your eye settings to 200ish..if that doesnt work,you might try replacing the eye.

[CockmyCocker]

ok iv gota new problem now for some its not a problem at all but a gift..if u love bounce when i pull the trigger in JUST 1 TIME it shoots 8 balls has this happend to anyone els?

[Flow_Tech]

try to lower your LPR a little bit,just above until it fully cocks and completes a cycle.lengthen your trigger pull a little bit,and take the frame off of the gun,screw the magnet in with a hex head towards the trigger and make the magnet screw and magnet touch,and you wont have bounce at all.

[CockmyCocker]

god i feel like a noob

guys all ur stuff has helped and worked thanks for the info but iv got one last thing when i shoot the balls just roll out of the barrel"well not really roll just wont go far at all" and they wont feed most if the time so im guessin its the bolt is to far forwords any help am i right how do i move the bolt back

[Flow_Tech]

ok,first things first.your back block SHOULD NOT be touching the body,there should be a gap when its completely closed thats about 2 papers width...to do this,take your bolt and cocking rod out,and screw the block out until its a VERY fine gap.replace the bolt and cocking rod back into the gun,and get some air if you do not already have some..turn your eblade on,go to the menu,not the TIMG menu,just the normal one and select classic mode,now,shoot without paint or a hopper and hold the trigger to see where the bolt stops after you pull and hold,if it does not clear the breach,that is your problem,so what you do is degas the gun,and take your cocking rod,and adjust it out towards you allowing the back block to move further back..do not move the whole entire rod,just the piece that twists on the end that looks like a nob,sometimes there is a small allen key screw in there,and just do little adjustments at a time,never make a big change,always go in small steps,and be sure to test after every movement.

[White_Noise]

ok,first things first.your back block SHOULD NOT be touching the body,there should be a gap when its completely closed thats about 2 papers width...to do this,take your bolt and cocking rod out,and screw the block out until its a VERY fine gap.replace the bolt and cocking rod back into the gun,and get some air if you do not already have some..turn your eblade on,go to the menu,not the TIMG menu,just the normal one and select classic mode,now,shoot without paint or a hopper and hold the trigger to see where the bolt stops after you pull and hold,if it does not clear the breach,that is your problem,

i agree up until this point. if the bolt doesnt clear the breech this is a problem, however, the way to adjust this is not by making the back block sit further away from the body. to cure this, keep the marker gased and in classic mode. holding the trigger back you will see it no clear the breech. turn the know on your lpr slightly clockwise(this increases cocking preasure) release and check again. do this until the tip of the bolt is flush with the back of the breech and you should be all good.

--mike

[CockmyCocker]

god

god i love u guys if i could kiss u i would "in a non homosexual way" thanks again

[TMAXXKING1]

here you go

http://www.air-powered.com/index.php?act=SF&f=2

look on there seems to cocker heaven

[White_Noise]

agreed airpowered has alot of info on cockers. ive used a lil info from them in the time that ive owned cockers, but most of my knwoledge came from A. the previous owner of my first cocker, and B. the knowledge gained from building my second cocker.