i Need help to stop my Xmag Bounce

[KostasXios]

I have a silver c&c Xmag with 4.01 version.
the DB scale is 1 - 10 and i have put it on 8. the gun bounce so i changed to 1 but still the same.can any body help me?
Thanks in advance!

[rkjunior303]

sounds like you are having issues with the 4.X, which were why it was never released. I'd have it flashed back to 3.2.

[Potatoboy]

You are using software that is not supported by AGD.

This is likely the cause of your problems.

You should send the marker to the party nearest you that can reprogram emag software.

BlackVCG in Oregon, AGD in Chicago, and Tunaman in New Jersey are just three of the locations.

[MindJob]

Talk to Z-man, he's knowledgable about the 4.0+ software. Everyone else is going to just tell you to have the gun re-flashed to 3.2


I am getting tired of waiting for software upgrades, so im sending my x-mag to Logic P.B. to have the predator II board installed.

[rkjunior303]

I am getting tired of waiting for software upgrades, so im sending my x-mag to Logic P.B. to have the predator II board installed.

unless things changed recently, 3.2 is the final version.

[REDRT]

Try not to have to reflash to 3.2 . 4.01 is better, but troubled in some markers. I'm not all that good with 4.01, but it seems to me Airguns Europe had something on this. If you were to flip the hall sensor a 180* if I remember right, it would help it out. Thats all I know.

[REDRT]

Talk to Z-man, he's knowledgable about the 4.0+ software. Everyone else is going to just tell you to have the gun re-flashed to 3.2


I am getting tired of waiting for software upgrades, so im sending my x-mag to Logic P.B. to have the predator II board installed.

You to, eh...

[MindJob]

You to, eh...

Yup. Im fustrated having such a capable marker limited by the software.

[KostasXios]

its quite dificult to send my marker to America.
i living in Greece.
any Idea about adjutments?

[REDRT]

page up

[REDRT]

I just took mine apart to see. I don't think my earlier suggestion is going to fly.

[KostasXios]

ok Red!i will try that

[Enemy]

debounce in 4.01 should go higher then 10!! now when you say bounce does it feel like the shots are smothed out when you walk the trigger or is it that you hit the trigger and the thing goes crazy?? the reason 4.01 isnt supported by agd is becaus it had issues with going full auto not because of anything else. if you run a high bps limit with a high debounce it should get everything back to the normal feel!

[KostasXios]

debounce in 4.01 should go higher then 10!! now when you say bounce does it feel like the shots are smothed out when you walk the trigger or is it that you hit the trigger and the thing goes crazy?? the reason 4.01 isnt supported by agd is becaus it had issues with going full auto not because of anything else. if you run a high bps limit with a high debounce it should get everything back to the normal feel!

i have adjust it to 10. i watched the marker to run full auto once. the marker bounce when i walk the trigger. shot by shot works properly.

[Z-man]

Sorry I am late. Here is what I can say on 4.0+

4.0 does have some quirks that do show up on some guns. Some have full auto issues that are not able to be resolved. However, there is another reason it might be bouncing.

Watch the sear pin and the trigger in E-Mode. If the pin touches the trigger at all (you could put a piece of paper behind the trigger so see if a mark is left) you need to either shorten your trigger pull or check to make sure that the sear rod is the correct length (2.125"). It could be too long and makeing E-Mode behave like Hybrid mode.

4.0 from my experience (and from what Miscue has told us) does not bounce or ramp so it's not a matter of shady software or "that is just how 4.0 works"