Hmm.. Makeshift Revy?

[personman]

Me and my stupid ideas strike. Well, I have been thinking.. If you drilled a hole in the back of a VL200, stuck a motor that fits the revy paddles in the hole, stick a paddle on the end, run a line down to the grip frame, drill a hole in the back of the grip frame where the palm of your hand goes, stick a electrical push switch so that only the button is showing outside the frame, and connect the wires, and connect the motor to a battery source.. well.. is it possible?(lol, please dont laf. I try to save money, thats all.. plus I dont think BE deserves to have my money.)
What I want it to do, is any time you push the button, the revy spins. methinks it would save battery power.

[personman]

*crycry* Noone can answer me!
GUESS IM TOO SMART FOR YOU GUYS! HAAHAH! lol, j/k

[ninja9876]

so your talkin about having the revy spin every time you pull the trigger...hum...yeah that would work. sounds like a pretty good idea actually

[personman]

no, not every time I pull the trigger, that would be an intelliframe setup. Im talking about putting a button on the back of the frame, so when I press the button, the revy spins.
read this.

http://store.airgun.com/acb/showdetl.cfm?&DID=17&Product_ID=11&CATID=5

[BEEFYSAUSAGE]

i dont see why not

it sounds good as long as you secure the servo motor in the hopper body i dont see a problem...just think like this
WHY NOT just give it a go....but if you stuff up you could reck your hopper(if your REALY bad with a soldering iron)
or your trigger frame..but if your happy to do it give it a go..oh and if you do drill or use a soldering iron cut from
the out side in and open it up and clean up the plastic that wells on the in side witha knife..
you know i mounted intellie feed on my sterling pump just so that i had it in it as well..
BEEFY.

[personman]

I looked at the servo motor on the dropzone paintball site, and it looks like it would connect to a computer chip of som sort, right? the board and the eye. makes sense, but my switch is electrical, so it only needs 2 wires connected to it.. is there some way to convert it?
or could I just buy a good ol regular motor like the ones you can get with some solar power car kits?

[BEEFYSAUSAGE]

ok

i have got mine hard wired (no board)i just connected the two black wires together(18volt or 2 9v batteries)ad the two red together ,conected black to one side of the servo motor and the red i conected to one side of a micro switch(any switch will work as long as it can take the power)and the other side of the switch i connected to the other terminal of the servo....you can do it with 1 9 volt battery
and it works too hope this helps(oh and i just butchered my 18 volt shredder to do it..it has worked fine for months)
BEEFY.

[personman]

I dont understand what you mean.. do you have a camera?
Here is what im talking about:
<img src="http://www.dropzonepaintball.com/assets/images/130662000s.jpg">

[BEEFYSAUSAGE]

ok

can you take the bottom off the servo and get a shot?
unfornatily i dont have a camera but ill try to find 1
BEEFY.

[personman]

*shruggs* I dont have a servo.. I want to know if I should order it or not first.

[personman]

let me just ask 1 question.
will this work? http://www.radioshack.com/product.as...5Fid=273%2D256
specs here:

http://www.radioshack.com/SupportGate.asp?SupportPage=%2Fsupport%5Fsupplies%2Fdoc19%2F19832%2Ehtm

[BEEFYSAUSAGE]

ok

that picture is exacialy what you need.. if you take the bottom of of that servo you will find 2 wires connecting to 2 terminals on the moter in side the black plastic case.. all your trying to do is rig up a circuit thatconnects it to a battery ...has anyone got a simple light circuit diagram..or if you can find 1 just subitute the light bulb for the servo moter(the 1 in the picture)
BEEFY.

[personman]

So your saying the servo will work if you take off the bottom? I know a little about wirez and junk and how to set them up.. I just kinda like to make sure it works.. you sure it works? Cause the servo is kinda expensive..

[personman]

oh forget it, I will just buy a java revy. Too complicated, and everyone is just telling me to go buy a revy.

[BEEFYSAUSAGE]

if i only had a camera

if i had one you would laugh at how easy it is but i dont ....so go and buy the revie as it will save you time and hastle
BEEFY.