The point it to keep the vert feed on thegun, warp feed would elimanate that. Thats why powerfeed is not anoption either.
-
** Your image was deleted because a huge ass "protection image" comes up. The site hosting that image doesnt allow for other sites to pull from it. Like Angelfire. So host it some where else or maybe attach it to a friendly corner post and link it from there. Sorry and thanks. - Webmaster **
Sly Irish Guy
-
Why do you insist on vert feed.
Comment
-
when you put two balls in, the second ball bouncing out is probably due mostly to the bolt nicking the ball and sending it flying out, not blowback, and the only things I can think of that -might- fix the 'problem' is a halo, or a warp feed which WILL fix the problem, whether used on a vert feed or PF. If you put a warp on your current vert feed your profile will be a bit higher than on a PF but thats just something you may just have to put up with if you want to keep your vert feed and shoot 13 BPS consistantly, presuming you actually -can- shoot that fast and not when your living in a little delusion.
Also, superbolt -might- help, as it would give you the same blowback reduction as a long nose bolt, and a longer bolt open time for another ball to enter into the breech.
Comment
-
Yep. What I was wondering earlier wasn't what blowback was, contrary to belief... but rather 'what blowback'?
Comment
-
-
If your bolt, barrel or both are very worn then air can leak around during fire. I have seen this and your can feel it if you put one ball in the gun and put your hand over the feed. I replaced the bolt and now have a new barrel. Also timing issues with the on/off being let out before the bolt is all the way back but, this is hard to believe could cause this also. Blow back is a problem or they would have stopped at standard feed. The constant press of a warp will fix this problem though. I hope this helps and good luck.Minimag mm17261
Dye SS 14"
114 C.I. Crossfire
CP Flame chrome drop
Boo-Yaah chrome grip
Reds pack
Lots and lots of paintComment
-
"i want to shoot at a constant 13 bps"
buy a warp, or go and get some balls..i could garentee that i can shoot as efectively at 7 bps as you can at a measly 12 bps ...learn how to play first and realise that not everyhing can shoot at 20 bps with no probs.Feel the fire ...Feel the passion..And let it consume all.......
smartmag(splash blue sm00672)
max attack 68ci 3000psi
Z Grip(Intellifeeded)
intellifeeded stock grip
16inch smartparts barrel
12 inch perfect bore ceramic series
18v shredder (old veiwloader)
and a good dose of class.Comment
-
so far, markhauguel has had the best answer to this problem, and i thank him. Warp feed isnt an option cus i like to be able to fire out of left and right sides of bunkers without rotating the gun 45 degrees. The reason i'm insisting on vert is because powerfeed drives me nutz. The only other thing i would shoot would be a standard right feed, cut down so the gun doesnt tilt to the right. Also people keep comenting on "if" i can fire 13 bps, the fact is i can, and please stop comenting on that cus its getting old. So yes thank you markhauguel for your post im going to try that wiht the new dye stainless thats in the mail and replace the longnose bolt.** Your image was deleted because a huge ass "protection image" comes up. The site hosting that image doesnt allow for other sites to pull from it. Like Angelfire. So host it some where else or maybe attach it to a friendly corner post and link it from there. Sorry and thanks. - Webmaster **
Sly Irish Guy Comment
-
Why not buy a vert feed body than and quit your moaning?Comment
-
elbow holes...
one thing you might try to dispurse the blowback a little more is to drill some holes in your elbow. Then some of the air can go out the holes instead of back up the tube into the hopper. Be careful though as it will decrease the strength and it might crack in half.
Also, when was your last tune up/parts kit? It is just a SWAG, but maybe a new spring would help...Comment
Comment