Barrel breaks at hgher rates of fire

[Ohms Law]

I have had the problem of breaking balls down the barrel at higher rates of fire for some time now. I don't think it is the paint because at lower bps, 14 or so, I don't have any breaks. But at 16 bps and higher I have alot of barrel breaks. I am using a level 10 X valve and have a good understanding of the system. I am using a HALO hopper with fresh batteries. Is it possible that the ball is not fully loaded in the breach and is being cracked by the bolt pressing the ball against the body breach? Any thoughts?

[flyingpootang]

I have had the problem of breaking balls down the barrel at higher rates of fire for some time now. I don't think it is the paint because at lower bps, 14 or so, I don't have any breaks. But at 16 bps and higher I have alot of barrel breaks. I am using a level 10 X valve and have a good understanding of the system. I am using a HALO hopper with fresh batteries. Is it possible that the ball is not fully loaded in the breach and is being cracked by the bolt pressing the ball against the body breach? Any thoughts?

Whats uo E over I/R (ohms law). Anyway you need to describe your marker setup in order to get an idea of what your talking about. For the basics check the ball to barrel size, if you have barrel nubbins check to see if they are not broken/sticking up, try a differnt brand of paint, try and remove all of the shims in your Lvl10

[FinchMan]

and is your velocity creeping up with the rof? I seriously doubt that would be it, but just a though.

[shades]

I get an occasional, what i call barrel "pop". Where the ball explodes at the end of the barrel. Its not a breach break because ther isnt any paint down the barrel.
this usually happens with old or brittle paint.

[flyingpootang]

I get an occasional, what i call barrel "pop". Where the ball explodes at the end of the barrel. Its not a breach break because ther isnt any paint down the barrel.
this usually happens with old or brittle paint.

Change the paint it sounds like it starts to breaking when fired and then as it accelerates down the barrel it comes apart right before exitting.

[Loguzzzzzz]

I am having a similar problem with my new G7. I am sending it to the tech next week but when I described the problem to him he stated that the spring in the detent could be too stiff. Maybe your detents need to be checked, cleaned or replaced.

Just a thought.

[ghost flanker]

Yeah, I had a similar problem with my X-Valved Automag. I was using ultra brittle marballizers, and almost every time I would shoot a string at high bps, I'd break paint. The marballizers were being chopped by the Level 10 as well as breaking down the end of the barrel.

[Ohms Law]

Thanks for the replies so far. I don't think it is the ball/barrel match because I size the barrel insert for the paint I'm using by the blow test. I even go one size larger to account for the occasional large or out of round ball. I'm using a ULE body and the detents are in good shape and are inserted in the breach just enough to prevent the ball from being pushed past the detent by the HALO. I know it is not the paint because I have had paint that was very hard and bouncy break down the barrel as well. When I get a break, there is paint just past the detents in the breach and all down the barrel. Remember this is only at high rates of fire ( above 16 BPS). Any more thoughts or do we think that the level 10 bolt is not soft enough for a ball that is not fully seated in the breach.

[Loguzzzzzz]

When I get a break, there is paint just past the detents in the breach and all down the barrel.

This is the exact reason why I said it could be the detents. Clean and lube them to be sure that they are free moving.

[Ohms Law]

This is the exact reason why I said it could be the detents. Clean and lube them to be sure that they are free moving.

They are not sticking. They move with ease.

[MoeMag]