Predator/Morlack mags - What are your settings?

[Resurection]

OK, so with my recent Devilmag runaway fun, I am curious what other folks are setting their dwell, debounce, ROF, AFA ROF, etc. at... here are my current settings on my Morlock with Pred 5.0:

Register .......... Setting
1 .................. 1 - Semi
2 .................. 16 - ROF
3 .................. 20 - AntiBounce (higher keeps gun from firing extra shots each pull)
4 .................. 15 - Dwell
5 .................. 6 - AFA ROF (ROF that needs to be hit for ramp to engage)
6 .................. 6 - AFA Shot Count (# of trigger pulls before ramp starts)
7 .................. 20 - Fire Hold Off (delay before fire after cycling in ms)
8 .................. 1 - Eye Hold Off (delay before gun will fire after seeing a ball in ms)
9 .................. 1 - AntiBolt Stick (1 = off)
10 .................. N/A - AntiBolt Stick Time
11 .................. 1 - Eye Off ROF (1 = rof set in Reg 2)
12 .................. 1 - ROF Additions in .20 of a second (1 = off)
13 .................. 1 - Disable Eye with trigger (1 = yes; holding trigger for 2 sec disables eyes)
14 .................. 1 - Clearing Shot (1 = yes; gun will fire if trigger held 3/4 of a sec with no ball detected by eyes)
15 .................. N/A - Not Used for my board

[REDRT]

I have older 3.0 software, but it is close enough. The only setting I play with normally is the ATB. Semi auto I turn it down to 4-6ms and ramping I turn it back up to 15-20ms.
BFD stays at 10ms
Fire hold off stays at 15ms
AFA level set to ramp after 2bps
Rate of fire normally always set at 15bps

[flyingpootang]

Morlock 5.0

1) 1
2)14
3)2
4)12
5)6
6)6
7)1
8)1
9)1
10)1
11)12
12)1

[Mechanic79]

latest 5.0 predator software on my Devilmag

Firing Mode:
1.2
Rate of Fire: This is the GLOBAL rate of fire. This controls the MROF in all modes with the eye
on. IF register 11 is set to 1 this will also be your EYE off MROF. Otherwise your eye off MROF is
controlled by the number you enter in register 11
3
Electronic and Mechanical Anti Bounce: A higher setting will keep the gun from firing extra
shots with each trigger pull. The board monitors the noise and firing rate then adjust the
mechanical debounce to work best with the electronic bounce settings.
4 Dwell: Bolt Forward Duration. Length of time the bolt stays forward
5
AFA ROF: 1 = off, 2 and above is the rate of fire that must be reached and maintained before the
advanced firing modes activate.
6 AFA Shot Count: Actual number of trigger pulls before ramping activates
7 Fire Hold Off: Delay before the gun will fire again after cycling, in ms
8
Eye Hold Off: Delay before the gun will fire after seeing a ball, in ms. If you are using a slow
hopper it might be necessary to increase this to avoid chopping.
9
Anti Bolt Stick: This is the time the board waits before increasing the dwell to compensate for a
gun that has an issue with bolt stick. NOTE: Using this feature on a gun without this issue will
result in the first shot being hotter.
1 = off 2 = 5s 3 = 10s 4 = 15s
10 Anti Bolt Stick Time: This is the increase in dwell when register 9 is engaged.
11
Eye Off Rate Of Fire: 1 = rate set in register 2, 2 and above equals the maximum rate of fire
when the eyes are turned off. Example: If this register is set to 1 then the rate of fire you select in
register 2 will be the same with the eyes on or off. If this is set to 11 then your eye off rate of fire
will be a maximum of 11 bps.
12 ROF Additions in .20 of a second: 1 = off, 2 = .20, 3 = .40, 4 = .60, 5 = .80
13
Disable Eye thru trigger: 1 = yes, 2 = no (this feature allows you to turn the eyes off by holding
the trigger back for 2 seconds)
1415

[11 Bravo]

The settings I use on my Predator Morlock 5.0 are Debounce 7, Dwell 3, and Fire hold off 5.
This is in a Hyperframe and has been very reliable and faaasssst.

[Rudz]

hmm

thanks guys..this is gonna be very benificail by the end of next week..devilmag baby!!!!

[Rudz]

yes

just got my devilmag today, i cant wait to air it up and rip on it..anyone else doing a magnetic trigger mod??

[Resurection]

just got my devilmag today, i cant wait to air it up and rip on it..anyone else doing a magnetic trigger mod??

....and? How was it?

[Mechanic79]

Devilmag 5.0 predator morlock board

1) 6 (worked with semi auto "1" as well about 12~14 bps) (I would assume FA "3" would also work)
2) 16
3) 5 (tried it at 4, didn't see much of a difference)
4) 12
5) 3
6) 6
7) 8 (12 was stock)
8) 4 (1 was stock)
9) 1
10) na
11-14) 1

These were the settings I finished the day with.
16bps ramping, eyes on, no chops, chuffs, misfeeds, etc.... (eggolution with z-board)

X-valve 5 shims (2 level X and 1 ULT shims to equal 5 ULT shim thickness)
Level X installed and tuned. (field strip screw tightened hand tight plus an 1/8th turn with allen key)

I shot approximatley 800 rounds of Draxxus Hellfire with a 684 insert. Chrono consistancy 288~295 fps

Setting that seemed to effect performance the most was #3, #7, and #8
I started the settings from stock or higher/slower then brought them down gradually until I ran out of time.

Mechanic79