Havin trouble with ULT on X-valve Can anyone help? U can read what i wrote in the forum.
-
-
might be able to help, however I cant find where you posted previously. copy the link or copy the text to here, and Ill try to help you -
Never mind I found it, and posted it here so others will help also
arplud223 wrote
I have a x-valve all tuned and threw the ult with all but last shim and get 1-2 shots and then won't fire . Should I start using LV Shims too? it seems like too much. I still have Tiny Black o-ring in Baggie. Am i supposed to install that as well? Did anyone have to adjust lx or x-valve after installing ULT? Have Nitro Duck Adjustable Tank set at 800psi maybe little more. Seemed to get worse as i added more shims ( No Runaway ) Rear screw for valve Needs to be real tight? Haven't oiled on\off yet Should I? valve has been oiled very recently. I think that all my Questions- Thanx
Is anyone gona answer? Caues my bolt is stickin now after all shims are in( it sticks after a good amount of shots ) its defin. not my LX caues that was workin perfectly before this. Unless you have to adjust it with this being in there( Which would be helpful if SOMEONE WOULD ANSWER .Comment
-
Some other things that would be helpful is which spring are you using on your level 10, and how many shims do you have in your ult (ult shims)?
If you are using the silver spring switch it to the red or gold one (just for testing purposes), and turn up the velocity. If your velocity is too low than it wont fire, or may only fire once.
Make sure you put a few drops of oil in your reg, and it wouldnt hurt to put it on your ult pin. The black oring should just be a spare, and there should already be one inside your ult. You need to take it apart to check. Is this a new or used Xvalve/level 10.
If it is a new level 10 make sure that the carrier tube that you are using is not too small. You dont want it to cause any friction on the bolt (this could cause it to stick) The bigger the better, but you dont want it to leak
Try some of these things, and either pm me or post here, and I/others will help. Good Luck and
GO VOLS (we are winning 14-0 vs Cal)
Comment
-
Been Tryin different Things...
I took a Shim out ( I had all in ) and it did'nt act up as much but the Bolt still stuck after 20-40 shots- I had it Chronoed at 260-270 Before i started F*ckin around with this ULT- It s pretty much A New X-valve Only About 1500 -2000 Balls Through it. Gona try a other Spring ( Have the Red one in now) What else would you Suggest for Stickin Bolt? The Little Black Oring is is there. I'm also gonna put some oil o the pin.Comment
-
I have 5 or 6 ult shims in mine. Your bolt sticking sounds like a friction problem. Check the detent also. Take it out to eliminate that. Go with the gold spring, and put a bigger carrier tube itn the level 10.Comment
-
If you already have the largest carrier that does'nt leak then feed it lots of oil.I had the same problem with mine.It worked fine until I put in the ult then the bolt stuck. I just keep messing around oiling it and shooting a few tanks of air then it worked like a charm.Originally posted by arplud223Comment
-
When changing carriers to a tighter one the amount of shims may affect the overal carrier o-ring tightness. In my Xvalve when I added more than 3 shims I had to switch to the next looset carrier.Comment
-
So You had to change Spacers? Thats what i was afraid of- I Had the gold spring in to begin with- not the red. I tried screwin with the velocity but to no avail. I 'll try going down a spacer- I gonna try Strechin the spring a little too. I never had a problem With the bolt stickin untill i started with the ULT.
I think i found the right amount of shims.( Is it true too little shims will make the bolt stick ? ) - its shoots real nice ( When the bolt is't stickin) Its gotta be the bolt now becaues ill get the hisses (out the Front) sometimes as well. Im out of air again so when i get air Ill tinker with it again. 
Comment
Comment