I recantly upgraded my Classic mag with an RT PRO valve and a lvl 10 bolt. I also have a single finger intelleframe. I was thinking of upgrading to a ULT trigger and a new grip frame. Other than the E-mag lower what would be the best double finger frame to get. I have seen a updated intelle frame or also the hyper frame. I have read that the hyper frame only get about 13 bps. I know thats still a lot but I was hoping for somthing with a little highr rate of fire? Any suggestions????
-
-
hyperframes get to 20 bps.and i happen to have one. the pull is light and not bad looking and theyre are some aftermarket parts for it from lukescustoms. -
It depends on the board in the hyperframe. Some do 20, some 13.Originally posted by olinarComment
-
Or you try and find a used Devilmag grip frame.
He doesn't do new one's as of now but you could try the buy/sell sectoin of the site.Comment
-
You have a single finger intelliframe?? I didnt think there was such a thing unless someone just basicly cut off the bottom half of a trigger.
A ULT will more than likely not work in a RT PRO valve. If you only have one oring in the bottom of it than it will not work. I know some people have them drilled out to accomidate the ULT, however it is probally cheaper if you just sell the RT Pro and buy an X valve instead of doing the change.
They make hyperframes both 20 and 13 bps. be careful most of the 20 bps frames are only simi. (ie no auto, hyper modes)
If you are wanting more than 13 bps you will probally want either A a Hyperframe, B a Boohyaah frame (15bps) or emag lowers.
The Boohyaah will be your cheapest option, and IMO they are better than the Hyper. (I have owned both) If I had to choose between all three it would defently have to be the emag lowers.
If you are intrested in a Boohyaah frame pm me and I can give you more specs on it. (Ie all the modes/options)
More than likely 13 bps is more than enough for you. That means in a 1 second 13 balls leave your gun and are spaced 23 feet apart from each ball. A person would have .07 seconds to react between balls. That is very fast, and I am sure that most people cant do it.
good luck
MannComment
-
The frame that I have is a single finger intella frame. I will attempt to attach a pic! I have been having trouble getting the lvl 10 to work, I'm working on that now infact..Comment
-
Apparently I don't know how to upload a pic. Anyway it looks like a standard frame with wood grips. I had to do the wireing myself so I know that it is infact an intella frame. I beleave it is one of the original that AGD made way back when.Comment
-
email me pics [email protected] and Ill post them for you. If it is indeed a single trigger I frame its probally rare, and worth some $$.Comment
-
Just sent the one that came out the best. I can get more if your interested. I just got hte LVL 10 eorking with the RT PRO valve. I'm amased at how much lighter the trigger pull is. I got it at the END of the season hear in michigan. I can't wait to see how well it works.Comment
-
that looks like a cf frame. They are very common. Can you get pics of the inside of it? What material is it made ofComment
-
Mabe build a Pnuemag (pnuematic automag). Or ask pnuemagger to do it for you.
HERE IS A VIDEO OF ONE OF HIS PNUEMAGS
I don't know much about them, but he does.Comment
-
Go with a spydermag conversion from lukescustoms.com with a Tboard and ramping chip. Then you'll have no problem keeping up with everything else out there..Comment
-
After looking at AGD website I think it is the CF frame and the guy I bought it from made it a intella frame. It has the sensor milled into it. I will get some pic's of the inside in just a bit. Got so mad at it when I was trying to get the LVL 10 working I almost threw it off my balcony!!! LOL seems to be working good at the moment though. Have to run more paint through it though. (I think my neighbors were getting mad!)Comment
Comment