emag problem for tuna or any agd tech ...

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • grominou69
    full time paintball addict
    • Jan 2003
    • 172
    #1

    emag problem for tuna or any agd tech ...

    ok here's the problem ....
    first i need to say that my emag worked flalessly and the lvl 10 is perfectly tuned since today ...
    i installed my fireblade trigger today ... everything was fine until i tried to fire the marker to adjust the trigger travel and stuff ...
    after i installed the trigger , the marker seems to have a software problem since i cant seem to be able to turn it on properly ...
    when i turn it on , instead of showing the agd 3.2 message on the display , some leds are lighting up randomly and so when i try to change the menu ... the only menu that shows properly when i cycle thru the menus is the test mode where trg is showing ....
    the 2 questions i have are:
    1- could the problem be the magnet coolhand send me with the fireblade is mounted the wrong side ?? btw can the hall sensor detect the magnet no matter wich side you mount it ??
    or could it be too strong that it affects the board electronics ??

    2- if not could i have fried someting just by tapping on the trigger pin to install it back ??

    anyways secundo , the marker don't fire either on mech but i thing this is because the sear rod is too short with the new fireblade ... could someone tell me if with a fireblade i have to lengten up the rod until the marker fires flawlessly on mech ??
    Tags: None
    • Tunaman
      Specialized AGD Tech

      • Dec 2000
      • 8643
      #2
      The magnet is too close to the HES. Back it off some. If it registers trigger pulls and activates the HES then the magnet is in the right way. Let me know how it goes.
      Email me for low prices on ALL AGD Products and more. [email protected]
      Tunamart

        Comment

        • grominou69
          full time paintball addict
          • Jan 2003
          • 172
          #3
          thanx i'll give it a try tomorow .... but you didnt answered my question .... did the hall sensor needs a specific pole from the magnet or it can be mounted either way ?? do agd minds wich side they mount their magnet when they assemble emag triggers ??
          because when i remove completely the magnet , the board isn't turning on as it was doing previously .... i don't see the menu anymore ... i hope i won't have to change the board

            Comment

            • MANN
              I am in TN. GO VOLS.
              • Apr 2006
              • 4266
              #4
              Originally posted by Tunaman
              The magnet is too close to the HES. Back it off some. If it registers trigger pulls and activates the HES then the magnet is in the right way. Let me know how it goes.
              Yes he did. Yes the magnet has to have a correct polarity when installing it

              AGD I am sure test all of their guns before they send them out the door

                Comment

                • grominou69
                  full time paintball addict
                  • Jan 2003
                  • 172
                  #5
                  ok backing up the magnet worked today so you where right ....
                  now i still have the issue of the gun not firing inmech but i know that have to do with the lenght of the sear rod .... when the trigger is fully pushed back , thhe rod barely moves ... and btw the rod is about 3/16" far from the trigger at rest so i assume i have to readjust it ...
                  did i have to know something before touching that .... will i have to put some loctite on the threaded part or it wont move by itself in normal operation ??

                    Comment

                    • athomas
                      Of course it works-its AGD
                      • Jan 2002
                      • 8039
                      #6
                      Yes, you have to adjust the trigger rod for proper operation in manual mode. If it seems easy to adjust after you break it free from the existing loctite, then you may want to apply new loctite.
                      Except for the Automag in front, its usually the man behind the equipment that counts.

                        Comment

                        • grominou69
                          full time paintball addict
                          • Jan 2003
                          • 172
                          #7
                          thanx a lot .... i played with that today and have it made firing .... but i can't remember how much free play do i have to leave between the trigger and the rod ??

                            Comment

                            • athomas
                              Of course it works-its AGD
                              • Jan 2002
                              • 8039
                              #8
                              As long as the trigger is not touching the rod while in electronic mode, you should be fine. I always adjust my gun to shoot properly in manual mode first, and then adjust my electronic stops and magnet to operate properly in electronic mode.
                              Except for the Automag in front, its usually the man behind the equipment that counts.

                                Comment

                                • FA22RaptorF22
                                  AO-CT
                                  • Nov 2006
                                  • 593
                                  #9
                                  This site will fix all your problems! Its great!

                                  http://www.havoc-online.com/

                                    Comment

                                    Previous template Next
                                    Working...