-
Greets Manuel
.:| levelx retro z-minimag |:..:| spearhead #192 |:.
.:| ---> looking for Flatline 4.5K or AA Apokalypse 2K <--- |:. -
Are you sure its chronoed at 270? Leaking out the back is generally associated with your velocity being too high,."I may be half human, but Im all Woman"
Retro PF Mag
Lvl 10
Intelliframe
DYE 12" aluminum'
KAPP foregrip
68/3k Flatline
KAPP DZ2
1987 VW Scirocco 16v
GOOD TRADERS: Alf, Snakestang
BAD: iNeedaN2tank! -
Big Problem
I dont know but I have noticed that this is a big problem for a lot of people .....I think someone should come up with an answer to solve all our prayers right away.I dont know but this always seems to happen to me even though all my orings are in perfect condition..Automag Classic P/F, 12 volt revvy, Lapco autospirit,PMI Perfect X-chamber, Crossfire 3000psi 68 ci Stubby,Retro Valve,AGD Intelliframe....
Part of Team Juggernauts Black!!Comment
-
Greets Manuel
.:| levelx retro z-minimag |:..:| spearhead #192 |:.
.:| ---> looking for Flatline 4.5K or AA Apokalypse 2K <--- |:.Comment
-
maybe your reg seat?
Comment
-
If I push the trigger a little bit, so that the trigger not shoots, but gives pressure to the On/Off, then the leaking stops.
The o-rings are all good.
HELP!!!Greets Manuel
.:| levelx retro z-minimag |:..:| spearhead #192 |:.
.:| ---> looking for Flatline 4.5K or AA Apokalypse 2K <--- |:.Comment
-
sounds to me like a reg seat problem try replacing it and see what happensRockin' the Cocker.
Great Traders List: DernComment
-
Greets Manuel
.:| levelx retro z-minimag |:..:| spearhead #192 |:.
.:| ---> looking for Flatline 4.5K or AA Apokalypse 2K <--- |:.Comment
-
Try oiling it.... put a few drops in the ASA, and gas her up.-Gig 'Em Ags!Comment
-
In the classics of this forum is an RT-Color Cut-Away drawing. Refer to that. Make sure your piston has a coating of light grease on it and the o-ring.Comment
-
is it leaking through the on/off pin? Mine was leaking when i put in the centerflag pin for my hyperframe, it turns out the orings i was using were a little too large for the centerflag pin, which would let a little gas out each time i fired, if i put enough pressure on the pin (manually via the hole on the hyper) it would stop leaking. I replaced the pin with the retro pin and it worked just fine, i then replaced all the orings with an RT Parts kit, and the leaking stopped with the center pin also..
Legion
Proud Owner of:
Emag #EM01523
Emag Powered 12v Smoke Warp Feed
Clear Blue HALO B
Total Freak Kit 14" Blue AA, SS Back
68 4500 Flatline
E-Magnum
Level 10
TL63 Blade TriggerComment
-
Greets Manuel
.:| levelx retro z-minimag |:..:| spearhead #192 |:.
.:| ---> looking for Flatline 4.5K or AA Apokalypse 2K <--- |:.Comment
-
Yah, my orings were yellowish, replaced them with new white looking ones, also oiling all the orings, especially the one in the on/off assembly (it is two separate pieces, there is an oring in the center, make sure that one is fine) and the one at the top of the on/off valve (inside the retro valve, i dont know what to call that oring), otherwise, yah, send it to AGD, they most likely wont charge you anything as it is probably under warranty service.
Legion
Proud Owner of:
Emag #EM01523
Emag Powered 12v Smoke Warp Feed
Clear Blue HALO B
Total Freak Kit 14" Blue AA, SS Back
68 4500 Flatline
E-Magnum
Level 10
TL63 Blade TriggerComment
-
call agd they will helpZ-griped, warped, retromag with super bolt, and warpleft polished body, freak kit and flatline 3kComment
ReTro leaking through back ...
Comment