Kila's latest creation....

[kilaueakid]

If I try to move the forgrip closer to gripframe, the screw would go into the ace board.

kila

[nato]

Didnt think about that... good call not drilling into the board You could still do it if you wanted to apply the time. It would be possible to use an internal band/clamp type thing for it to wrap around the rail. Otherwise it is still pimptacular. LATER.

N.A.T.O.

[chizle97]

i would like to say awsome job and sweetness too I dont know how ya did it but it looks awsome.

[FooTemps]

AHHH! I keep coming back to look at this beauty! Dude, this emag is just awesome. lol

[DocRocker]

where's the hall sensor?

[hitech]

It was my understanding that the UTL trigger did not provide enough return force to work well in an eMag. I thought this would work. What do you think?

[Smitty2k1]

Ok, since I still dont own a mag, and am currently finalizing the botom line setup on the one im getting... what verticle adapter is that? Is it part of the foregrip or what?

The only way I can seem to use a gas thru grip (I plan on using a gas thru grip, but not using the gas thru part) is by using one of the full size adapters, and they are quite long and lower the foregrip very far... since I have a y-grip on the way, this is bad as it interferes with the dropforward.

Ok long story short, is your foregrip setup one piece or is it a foregrip and an adapter?

[FooTemps]

Originally posted by Smitty2k1
Ok, since I still dont own a mag, and am currently finalizing the botom line setup on the one im getting... what verticle adapter is that? Is it part of the foregrip or what?

The only way I can seem to use a gas thru grip (I plan on using a gas thru grip, but not using the gas thru part) is by using one of the full size adapters, and they are quite long and lower the foregrip very far... since I have a y-grip on the way, this is bad as it interferes with the dropforward.

Ok long story short, is your foregrip setup one piece or is it a foregrip and an adapter?

Uhhh that's not a gas tru foregrip...

BTW kila: That foregrip looks really ugly... you should change it

Originally posted by hitech
It was my understanding that the UTL trigger did not provide enough return force to work well in an eMag. I thought this would work. What do you think?

He said he'd use a smaller noid. That might work better since there is less mass to push back on the return.

[kilaueakid]

Call the forgrip ugly or what you will, but it feels better than anthing else I have used. Yes it was a gas-through forgrip. It is a stock AGD gas-threw forgrip. I bored it out and lightened it as I don't run my airline through it.

Hall sensor is mounted in the gripframe under the selector switch on the right side when looking down the barrel.

~Kila

[FooTemps]

Originally posted by kilaueakid
Call the forgrip ugly or what you will, but it feels better than anthing else I have used.

You haven't used my foregrip yet. It's like your's. It has gas thru, rubber, grip and all that but it's shorter and the rubber looks better. (I think it came off a bike, lol)

[zeroack]

Halo question...

I've been looking at your mag here and I have the same problem as many that have posted here...I keep coming back and looking at this mag. I've made up my mind to own a mag now after playing with a buddies rig this weekend. My one pounding question is how did you get that halo so low? Is that a typical mod for mags that run halos?

Thanks...

Zero

[FooTemps]

Re: Halo question...

Originally posted by zeroack
I've been looking at your mag here and I have the same problem as many that have posted here...I keep coming back and looking at this mag. I've made up my mind to own a mag now after playing with a buddies rig this weekend. My one pounding question is how did you get that halo so low? Is that a typical mod for mags that run halos?

Thanks...

Zero

Actually, the halo was modded.

[zeroack]

ok follow up question...

How was the halo moded?

tanx...

zero

[FooTemps]

Re: Kila's latest creation....

Originally posted by kilaueakid
The Halo shows the meaning of a true No-rise....no eye sensors in this Halo, she has ears works with every shot of the marker.

There you go. That's how he modded the halo.

[kilaueakid]

I guess you could re-locate the eyes further up on the halo, however I do not use the eyes on this one. I can't say a whole lot about this halo right now, but in time, I'm sure you will be hearing more about it.

kila