Building a Warp ULE Automag...

[Pariel]

Frame Grip Assembly w/ Grip-$25(@airgundesigns online store)
Warp Feed ULE Main Body-$145(@airgundesigns online store)
Warp Feed-$130(paintballgear.com@actionvillage)
Empire Reloader-$60(@paintball-discounters.com)
68 ci 4500 psi Crossfire Tank w/ Redz Tank cover-$184(@actionvillage)
LvL 10 Kit(?)-$68(@actionvillage)
Automag gas through Foregrip-$16(@airgundesigns online store)
bottom bottle adapter-$15(@airgundesigns online store)
steel braided hose-$depends on length

Total-$627+

i also have some questions-
-is the Y-Grip also and an intelliframe? can i get one that ISN'T an intellframe?
-what length steel hose do i need? should i run the hose through the foregrip or through the back? this is my first mag, so i'm not sure how they're set up, i will try to take a look at one in person to see how it's set up though.
-***Do I have everything I need?***

[mbyankee10]

your on the right track

you need to shop around on here thats alot to spend on parts what kind of vavle you going to use look on ebay you can prob get an e mag or something for that amount of money

[Pariel]

I personally don't care if i'm paying equal to an e-mag, i want the experience of putting together my own gun. so, with that in mind, any other suggestions? i listed these prices because i knew them, and i knew what i THINK i need, but i want to know if i've got it right.

what exactly do you mean by "valve"? i thought that was included in the lvl 10. please explain.

[mbyankee10]

you need a valve level ten is just a bolt

the valve is the main part og a mag you need either a
clasic valve 75-100$ on ebay
rt/emag valve 120-150 On ebay
or an x valve 265-325
go to www.airgun.com tech section
they have diagrahm.
thats why i suggested you find a used one and up grade it with parts you want building a mag from scratch is not complicated you can get one and take is apart and put it together in like 20 minutes.
but do what you want to do.
with what you want you can find one here in the f/s forum for alot less
this is a decent deal
http://cgi.ebay.com/ws/eBayISAPI.dll...category=47252

[Pariel]

The thing is, the gun i'm putting together is gonna be my dream gun basically-i don't think many other people have ANYTHING like it. i could get some parts, but i'd rather just buy everything new.

[mbyankee10]

like i said you can do what you want

but you can buy an rt pro (brand new) and add a warp ule body and it will cost you less. and that exactly what your building.

good luck

[tony emerson]

I think you are missing some stuff some screws and i didnt see a rail. PM Tunaman and ask him to sell you a "kit" that you can put together.
or go to his site http://www.tunamart.com/

[Pariel]

i was gonna pick up screws at the local hardware store, and i though that you didn't need a rail? my friend took his off, his gun works fine...

[mbyankee10]

i dont mean to sound like i know it all but

you need to do some more research before you embark on this.i think you need to learn some more about mags and seriously look at the cost a new agd rt pro with a warp body is 599 at the agd store you can find some cheaper other places and have a fully to gether working gun.

this wont be your dream gun at the rate your going!!!
especially at about 800 for just the parts and stuff.

[Pariel]

you keep mentioning money, but the thing is, if i'm gonna build my own gun, i'll just save till i can buy it...simple as that.

btw, think i'm gonna pick up an automag on ebay and customize it up..ULE warp main body, warp feed, empire reloader...maybe x-valve

[atcer]

i have heard that the empire reloaders and the warp dont play nice together becuase of a sound sensor location issue... i would suggest a halo or if cost is a factor get a halo TSA backman... that way the paddles push the direction of the warp tiltage...

[Pariel]

didn't know that...ok, i'll deffinately look into, if i go a halo, it'll be a backman (higher end halos are EXPENSIVE! specially when i'm using it AND a warp...like paying for 2 hoppers...)

[tony3]

or you could just get a revvy.........

[p8ntball1016]

or you could build your own crank operated revvy.

[FragTek]

I'll hook you up with the warpy...

http://www.automags.org/forums/showthread.php?s=&threadid=109580

Check that bad mofo out... Don't get much better than that!