Pneumatic Trigger Frame v2.0 !!!!!!

[phishphen]

Links

just to let everyone know, i just switched internet service providers so the site that i have all my pictures, videos, and documents is going to be no more soon.....im gonna get another site up with my new ISP and re-link everything....so if you try to clik on a link and it no work, check back in a few weeks.......

[luke]

Hey guys I have some spare parts I need to get rid of.

This is a "NO PROFIT" deal to me.

Parts are new from Clippard.

Go here>> (post #10)

http://www.automags.org/forums/showthread.php?p=1646435#post1646435

[Gunitwanksta]

after reading all over about this it just seems to me that its a pneumatic assist trigger. does pulling the trigger still trip the sear when air is not supplied to the pneumatics?

[warbeak2099]

Of course not. The ram trips the sear when you pull back on the 3-way. If there's no gas then pulling back on the actuator obviously isn't going to open the ram.

[ShadowNife]

hey guys, im making a model out of foam first to see where to best position the stuff inside my y-grip. However, I don't know the measurements of all the parts involved in this. Could someone who has done this mod or know/have the parts give me the measurements so I can plan this out ahead of time?


thx to anyone who can help.

[Tim Taylor]

[EnW]

A little problem...

I finished my pneumatic install in an Itelliframed, X-Valved, MicroMag with a ULE trigger.
I do not know the exact output pressure of the Palmer's Micro Rock, but it is set to allow the gun to shoot and then a quarter turn higher.
My problem seems to be short stroking. I can shoot slow, individual shots, but if I try to shoot a couple back to back, the marker chuffs and double feeds.
Does the pressure of the Micro Rock need to be higher?
Any help is appreciated.
Eric

[nuclear zombie]

Thanks I shot 2 tanks of air thru it and it started working properly. I also measured the trigger pull at 6.9 ounces with the clippard 3way (spring removed) and the travel was at 1 mm

i just picked up a smav-3 today , haven't had much time to look at it , so what's the easiest way to get it apart?

[Bossman]

I finished my pneumatic install in an Itelliframed, X-Valved, MicroMag with a ULE trigger.
I do not know the exact output pressure of the Palmer's Micro Rock, but it is set to allow the gun to shoot and then a quarter turn higher.
My problem seems to be short stroking. I can shoot slow, individual shots, but if I try to shoot a couple back to back, the marker chuffs and double feeds.
Does the pressure of the Micro Rock need to be higher?
Any help is appreciated.
Eric

Turning up the pressure seemed to get rid of my chuffing problem. At first I set mine up the same way you did.."I do not know the exact output pressure of the Palmer's Micro Rock, but it is set to allow the gun to shoot and then a quarter turn higher." But I got a lot of cuffing. Turning up the pressure made it shoot like a dream, and didn't even make the trigger that much heavier. Hope that helps

[nuclear zombie]

how do I get the Parker SMAV-3 apart to get the spring out?
I tried taking the back barb off but only ended up breaking it off.I'd like to be able to salvage this one if possible otherwise i'm going to open it up with a dremel tool and attempt to build a one piece 3-way/actuator assembly.

["Joe"]

Any one have the how-to? Links don't work anymore

[Wassupstranger67]

The ring around the pin is pressed in there. Just vice up the smav3 and pull the pin with some pliers. Be careful things will fly out

[OneEyedPimp]

Any one have the how-to? Links don't work anymore

I would also like a copy as the comp I had it on crashed.

[frontsniper]

I would also like a copy as the comp I had it on crashed.

Is there something wrong with Earthlink? Links don't work(sorry if I repeated but I didn't get it saved on my comp.

[1337caesar]

anyone wanting the file e-mail me at [email protected] I still have a copy. dont post here because I may not check this thread for a couple weeks at a time

Edit

The file is too large, I cant e-mail it. If someone who can e-mail 30 mb files wants to get it I may be able to msn it to you but e-mail just wont work