Help me with Project Herbavore(AKA Yellowjacket)!

[anomoly40]

~DISCLAIMER~ I know this is automags.org. I know this isn't an automag project. What I do know is that there are some of the smartest paintballers on this forum and if they can't help me, no one can.~DISCLAIMER~


I have a project I am working on that I need additional input on. First let me tell you the concept behind this project. Basically it's an half-blocked mQ-ed cocker. Except the ram is behind the bolt instead of in front of or beside it. Now for the question I have, are there any other frame besides the Eclipse frame that has two different outputs(like for two different solenoids)? You are about to ask why. The reason is I want the solenoid inside the grip frame (like a Timmy) so the outside isn't cluttered. I know the Eclipse frame has two solenoids. I know the mQ takes over the operation of one of the noids. I want the other one to be inside of the frame and I don't want to have to cut and drill on a perfectly good frame.

WHOO PICTURES!

<a href='http://putfile.com/pic.php?pic=2/3201005663.jpg&s=x2' target='_blank'><img src='http://x2.putfile.com/2/3201005663-thumb.jpg' alt='Click to enlarge'></a>

<a href='http://putfile.com/pic.php?pic=2/3201011997.jpg&s=x2' target='_blank'><img src='http://x2.putfile.com/2/3201011997-thumb.jpg' alt='Click to enlarge.'></a>

<a href='http://putfile.com/pic.php?pic=2/3201003368.jpg&s=x2' target='_blank'><img src='http://x2.putfile.com/2/3201003368-thumb.jpg' alt='Click to enlarge.'></a>


The bolt is orange. The ram is blue. The hoses that go to the solenoid are dark purple. The airchamber is green, I made this so there isn't a hose running down the side of the marker (in other words, I don't know why). The hose going to the input barb on the noid is light purple, and the LPR is red.

[anomoly40]

Does anyone have a Morlock board for sale?

[FinchMan]

i don't know autocockers too well, but wouldn't there be some room where the hammer used to be, or does the mq valve take up all the space in the lower tube?

I'd think that you could fit a ram in their, and hook it to the sled/backblock that goes on the bolt. that could hide it well.

then again, i don't know cockers well at all... so thats my $0.02

[neppo1345]

you can usually fit the cocking noid in if you make up a spacer between the grip frame and body...I've seen it done, I'll try and find some pictures...

[anomoly40]

I was thinking about doing it with a timmy clamshell. Make it kinda like a spimmy. I know it has a noid in the frame already, I could just put the mQ in a spyder body then cut the top tube and make a bracket to hold the ram.

To answer the question about the mQ, It has a spacer that takes up most of the room in the bottom tube. I'm thinking with my routing of the hoses through the "extra space" would take up the rest of it. It shows the cutaway here.

I'll ask again, Does anybody have a morlock or even better a preadator'd morlock for sale?

[Joni]

It's been a while since i bought my mini morlock, but at the time a predatored morlock couldn't run a double soleonid marker. Could be a different story now, just giving you a heads up.

[anomoly40]

Yeah I'm just going to make a spimmy for now. Does any one have timmy parts for sale? It might be a while but I like to plan ahead.

[11 Bravo]

It's been a while since i bought my mini morlock, but at the time a predatored morlock couldn't run a double soleonid marker. Could be a different story now, just giving you a heads up.

A Mini Morlock with the stock Morlock code can run double solenoids.
Just FYI.