Anyone have Dimensions of an AGD stainless body?

[Pneumagger]

I want to mill an aluminum body that accepts twistlock barrels and still has a vertical removable feedneck.
What can I say... I love me some twistlock barrels

[Will Wood]

I have a couple old SS kicking around... I'll search for and post up later.
(I got a nice centerfeed barrel (JJ 2 peice? something like that..) too that has been sitting in my closest for 4 years... /plug)

ok..

6 1/4 long.
about 1 1/4 circumference

Feed hole from 2 1/4 to 3 from front .
twist lock thingy from like 2 to 2 1/2 (you'd best line it up on your rail and stuff)
anything else you need on it?

[questionful]

You should call the factory? But. . .

With some calipers I inherited from my grandpa:

OD= 1.123"
ID= 1.002"
Length= 6.258"

Start of on/off hole (from back of body)= 0.122"
Diameter of on/off hole= 0.231"
Start of Sear Slot (from back)= 1.477"
Length of Sear Slot= 1.429"
Start of Front Frame Screw Hole (from back of body to tip of rear threads)= 3.902"
Start of Twistlock Hole (from back of body)= 4.33"
Diameter of Twistlock Hole= 0.268"

You should know that there is a ~2mm gap between the mainbody and the valve on my mag. Might be the body's fault, might not. And I didn't measure the breach because I can't do it accurately due to the powerfeed being in the way.

[MoeMag]

My findings.

OD= 1.120"
ID= 1.050"
Length= 6.258"

Start of on/off hole (from back of body)= 0.122"
Diameter of on/off hole= 0.225"
Start of Sear Slot (from back)= 1.475"
Length of Sear Slot= 1.425"
Start of Front Frame Screw Hole (from back of body to tip of rear threads)= 3.902"
Start of Twistlock Hole (from back of body)= 4.33"
Diameter of Twistlock Hole= 0.266"


Mostly the same. What is AGD's tol?

[Pneumagger]

Would someone mind mailing me a spare body, I can have it measured and back ASAP. I'll cover your fees as well. Not that I don't trust ya'll... I just like having firsthand info.

[st6212]

Wouldn't it be easier to modify an existing ULE body or get hold of a sluggo? ie ream out the cocker threads and add an extra hole for the twistlock etc.

Or are the dimensions smaller than the stainless bodies? I forget, been years since I've looked at a classic body.

[Pneumagger]

Wouldn't it be easier to modify an existing ULE body or get hold of a sluggo? ie ream out the cocker threads and add an extra hole for the twistlock etc.

Or are the dimensions smaller than the stainless bodies? I forget, been years since I've looked at a classic body.

This is not for a mag. I simply stated I want to mill an aluminum body to accept a vertical twistlock barrel. Hence, I need accurate female twistlock dimensions.

[Will Wood]

I can get one off to you.
Hit me up with a PM or Email.

And I'm curious how a mag barrel would fit in something else? Maybe it's simple but I wouldn't think it could.

[TheTramp]

[questionful]

Metal around the twistlock pin isn't really necessary though.

TWISTLOCK & BREACH DROP FTW!!!

pneumagger, idk exactly what you're doing, but I sense impending awesomeness. . .

[Lenny]

Joe, I have a vert feed SS body I can drop off to you for a few days. Give me a call.

[Pneumagger]

Joe, I have a vert feed SS body I can drop off to you for a few days. Give me a call.

I need your number... new cellphone (lost all the old numbers)

[ClassicMagger]

Hey:

Joe-if you need one let me know. I have to mail you some stuff anyways and you can keep the body for awhile. I also, have some twistlock assemblies if you need some of those too.

-ClassicMagger

[magmonkey]

if I can get an ok with agd I will make you a solid and prints

[Lenny]

I need your number... new cellphone (lost all the old numbers)

PM'd it to ya