Electro?

[NeedForSpeed]

I don't want to sound like I'm trying to capitalize on your post, but i have a Ripper 2 and LNIB Quest I've decided to sell. The first of which the proceeds will go to Speed The Light. Both for less than $400 and both are amazing markers. These days..you can find a DM6 or Ego 06 for about $400. I've owned almost every marker from the year 2006 and some 2007 markers but I'm actually looking to build a Mag now so I guess that could tell you something. I'm either somewhat of a gun whore...or that stuff just isn't good enough

[Hilltop Customs]

Is this like an egomag thing? I have an intelli frame so it might not all fit. I could get another ram and then switch out frames when i wanted to. humm...

They way I have mine planned out is to put the 9 volt in the bottom of the grip then the board mounted to the top of the 9 volt, just like the picture except with the 9 volt adapter sandwiched between:


then the noid on top of that.

It does involve some trimming out of the grip...I took out the cross brace in my intelli and now I can fit 9 volt in easy...but to fit the noid it will require some material to be removed directly behind the trigger. The noid has to be placed high in the grip frame(right below the sear in fact sear might need trimmed for it) right where the tail extends out. The output of the noid would be directly behind the trigger...the hose would make a U turn right into the back of the ram.

It will be a tight fit, but I think it should all fit in a intelli. It might require the very tip of the sear to be either ground down or cut off. It would be nice to just grind it down a little so it can still be used as a mech mag, but i think it will need cut at least to the hole.

Hopefully after I sell some crap I can finish mine and throw up a how to. Till then I hope my description helps haha

[Hilltop Customs]

or u could take an ion board and put into a frame like im doing right now. stock ion boards are cheap and everything is there, u could even put eyes on it with no problem.

How are you planning on using the ion board? i'm imagining your using its noid too? if not can you take the capaciter off cause its huge.

If your using the noid....mind explaining how cause its normally open?

[sandfreestyle]

well the board is coming in the mail right now so i cant tell u exactly how im going to do it yet, but ive seen people do it before with out any modes to the board. pm me about ur ripper 2

[robnix]

They way I have mine planned out is to put the 9 volt in the bottom of the grip then the board mounted to the top of the 9 volt, just like the picture except with the 9 volt adapter sandwiched between:


then the noid on top of that.

It does involve some trimming out of the grip...I took out the cross brace in my intelli and now I can fit 9 volt in easy...but to fit the noid it will require some material to be removed directly behind the trigger. The noid has to be placed high in the grip frame(right below the sear in fact sear might need trimmed for it) right where the tail extends out. The output of the noid would be directly behind the trigger...the hose would make a U turn right into the back of the ram.

It will be a tight fit, but I think it should all fit in a intelli. It might require the very tip of the sear to be either ground down or cut off. It would be nice to just grind it down a little so it can still be used as a mech mag, but i think it will need cut at least to the hole.

Hopefully after I sell some crap I can finish mine and throw up a how to. Till then I hope my description helps haha

Take a look at lukes Intelliframe Mounting Plate and Intelliframe Milling:

http://www.lukescustoms.com/page0027.htm

[Hilltop Customs]

Take a look at lukes Intelliframe Mounting Plate and Intelliframe Milling:

http://www.lukescustoms.com/page0027.htm

Woah, thats almost the same as mine except I didnt take out the channel the whole way to the bottom. I think my channel is a little deeper(toward the trigger) too. Looks great though. Luke is always coming out with great stuff!

[sandfreestyle]

I don't want to sound like I'm trying to capitalize on your post, but i have a Ripper 2 and LNIB Quest I've decided to sell. The first of which the proceeds will go to Speed The Light. Both for less than $400 and both are amazing markers. These days..you can find a DM6 or Ego 06 for about $400. I've owned almost every marker from the year 2006 and some 2007 markers but I'm actually looking to build a Mag now so I guess that could tell you something. I'm either somewhat of a gun whore...or that stuff just isn't good enough

how much for the ripper and wat color?

[punkrex]

I have my pneumag and a tippmann 98 rt but also want a quality electro for less than $400
any ideas

I recently purchased an AKA viking and it is by far the best marker I have shot (I've only shot a few electros). Looks like my mag is going to be demoted to a back up.