Is warp hose the same a qloader hose? Also if people have any creative ideas for mounting qloaders.
-
-
No, the hoses are different. The o-rings that the q-loader hoses use will not fit over a warp hose. -
Warp hose and qloader hose are very different. What are you mounting the qloader to?Comment
-
I have a ule vert and want to have the hose as low as possible without haveing to spend more mony for the warp ule. I had an idea using one of the warp attachments.Comment
-
Here's is my e-mag with the Q ion mod kit on top and a copper elbow I used on the socket.
Comment
-
Here's is my e-mag with the Q ion mod kit on top and a copper elbow I used on the socket.
[IMG]http://i4.photobucket.com/albums/y127/medicx/Markers/Picture170.jpg
im assumming you used a large screw and replaced the batt thumbscrew to mount the q?
What feedneck is that?Comment
-
That is correct sir, I believe it was a 2.5" 10/32nds screw. I also have a piece of AL inside the void of the SMS and a small piece of neoprene between the battery housing and the socket. You can see it if you look closely. Works out perfect! Ya its a bit of a pain to pull off the socket to get the battery off but with KC's battery, I don't have to charge much.
Feedneck? That is the Ion mod kit from QLoader.
Comment
-
That is correct sir, I believe it was a 2.5" 10/32nds screw. I also have a piece of AL inside the void of the SMS and a small piece of neoprene between the battery housing and the socket. You can see it if you look closely. Works out perfect! Ya its a bit of a pain to pull off the socket to get the battery off but with KC's battery, I don't have to charge much. Feedneck? That is the Ion mod kit from QLoader.
Ion's are angel threaded?Comment
-
I loved how you set up the Q. Can you post some more pics of it, including one of the socket, without the tube? And I liked you "thumb screw" as well. That's a beautifull e-Mag you have there!That is correct sir, I believe it was a 2.5" 10/32nds screw. I also have a piece of AL inside the void of the SMS and a small piece of neoprene between the battery housing and the socket. You can see it if you look closely. Works out perfect! Ya its a bit of a pain to pull off the socket to get the battery off but with KC's battery, I don't have to charge much. Feedneck? That is the Ion mod kit from QLoader.
Comment
-
They are not exact but the thread size is very close. Angel thread size is M21 x 0.75 and Ion thread size is 13/16-32.Originally posted by Ruler_MarkComment
-
ahh, I'm gunna cut down a warpfeed adpter and 90* elbow to achieve the same thing hopefully.They are not exact but the thread size is very close. Angel thread size is M21 x 0.75 and Ion thread size is 13/16-32.Comment
-
Not completely true. You can use q-loader o-rings on a warp hose and force the hose into a q-loader socket and have it work. This is what I did for my mag. The o-ring does not fit properly in the grooves of the hose, but if you work the hose enough, it will fit very snug.Originally posted by warbeak2099
Here's a visual pic of the differences in hoses.
Top to bottom:
Super hose
warp hose
q-loader hose
Comment
-
I ran Warp hose on my Etac and it was ideal. The metal spiral support will keep your balls from getting crushed (
) if you take a hit there. Paint flows much better too. The Q hose is crap.
Here ya go. Q mounted on Warp plate, high and tight.
Comment
-
thanks guys. So let me gets this straight. You can use the qloader ion feed neck on a ule so you can slip an elbow over it. Then you say that warp hose is better than q and will sort of work. Is this right? I want to have the hose like medcics but the pod mounted like warwitch but up higher. I was thiking of mounting the warp adapter underneath the rail where people sometimes put asas the old school style. will this work. btw sweet setups everyone
Comment
-
one of my first qloaded mags...........
Comment
Comment