cyborg questions
i dont have a manual, and cant seem to figure out whats going on with this 06 cyborg. i cant change modes as per macdevs site and cant turn off the eyes to do a dry fire. any help at all would be appreciated. thanx
-
-
allready
, pm behemoth I think he has had quite a few
-
MacDev - USA
North and South American Headquarters
13200 NW 43 Avenue
Miami, Florida
USA 33054
Ph: +1 305 681 4385
Fx: +1 305 953 3843
Mail: [email protected]
What board is in it ?
Theres several versions on the PDF file section.
Comment
-
Originally posted by rednosepit79
You may have the 07 board. Either way, you should just be able to hold the trigger back for a few seconds to turn the eyes off.
Well, let me ask you, is the LED that lights up multi colored, or is it just white?Comment
-
not sure what board, but when i hold the trigger down it flashes red , but still wont dry fire. the led is multi colored.
Originally posted by BigEvilComment
-
I had an 05 that had a Tadao board in it. Its LED lighting was multi colored.Originally posted by rednosepit79
Did you open the grip panel and look for markings on the board ?Comment
-
its an macdev board , it has a set of dip switches next to where the battery restsit airs up fine w/ no leaks. if that helps at all
Originally posted by going_homeComment
-
lol yeah man, its my luck i guess.thanks for the adv. ill pm him right away.
Originally posted by maniacmechanicallready , pm behemoth I think he has had quite a fewComment
-
Peanut Butter Nation
I hate to send you to kindergarten but there is a large presence there, maybe you can get some help there ?
Comment
-
lol, was kinda avoiding there but ill take a look any way. thank you very much for your help.
hopefully i can get this straightened out.
Originally posted by going_homeI hate to send you to kindergarten but there is a large presence there, maybe you can get some help there ?
Comment
-
if i remember correctly the 2 dipswitches are for tourny lock. not sure how you want them set, but it sounds like you have tourny lock ont33kyboy "So if a cat is dropped from 11 inches, it will most likely die."Comment
-
1) replace battery?Originally posted by rednosepit79
general fyi
turn it on, should be red led, slide the bolt forward should go green indicating eyes detect paint.
hold the trigger down and turn the gun on, should be blue indicating board option selection mode.
If you turn the gun on and have the bolt back, the red light will flash white one time when you press teh trigger, indicating sensing trigger pull but eyes did not detect paint.
If you aren't getting any clicking when holding the trigger down while LED is red, its could be your board/solenoid wire is loose or the solenoid is bad?
post details and I can recreate on my 06 and maybe help you out?"Accuracy by volume has been, and will remain, the best way to score eliminations" Tom Kaye
FeedBack
[email protected]Comment
-
aleady changed batt. eyes r good, but not getting the clicking sound ur refering too. the wire is seated , the only clicking is from the trigger switch. should i change wire to solenoid or get a whole new noid? thanks -dennis
Originally posted by Oregon_pb_Comment
-
Get a wiring diagram for that board and make sure that everything is plugged into where it belongs. All of those connectors are the same and its easy to make a mistake.
Here are some links that may or may not help
Last edited by BigEvil; 08-05-2008, 06:30 AM.Comment
-
Just so everyone knows, this was my cyborg I sent to him. I tested it before I sent it, so I'm not sure what happened.
Here's what I'd suggest:
-Try it with air and paint
-Post this on the macdev forum
-Make sure it's not in tourney mode
-Check the activation screw in the trigger, as well as the rear-travel screw
One way or the other, we'll get this resolved, even if I have to buy a replacement part for him. I'm 99% sure, however, that something just needs to be adjusted.
One last question. Do the eyes light up when the marker is turned on?Comment
Comment