Well it was a long battle to bring me and P8nt's new UTB based Emag board to life. but after fighting the board forever, I finally completed it and had it shipped off to P8nt for final review and to start selling. SO BE ON THE LOOKOUT FOR IT THIS WEEK IN THE DEALER SECTION!!!!!
But to the point of this thread. Now that i have completed the new Emag board, i am looking for the next board to do. I have been working on repairing a handful of hyperframe boards and have run into the problem with one board having the main chip fried. So without having a programmer/software for the chip (and because i have 500 Atmel chips in stock), i got to thinking. Why not bring Xmod to hyperframes and any other possible marker out there.
With that said, i know many of you have the Xmod programmers laying around collecting dust.....while you have other electrical markers laying around needing some nice new software. So I would like to ask all that are reading this to post some markers that Xmod would be greatly wanted for. Now dont forget old markers like B2K's and even rain makers! Anything running off an electric board i can make happen.
Now with that said, i want to openly ask LorneCash for help on this on this (since i cant get ahold of him privatly). I know you want to get the rest of your programmers sold and earn a bit more on your awsome software. So would you be willing to help change the software to work for 12 and 9 volts systems and help with any questions i might have with the software technically? this would of course give you the chance to get your code protected and safe like you really want (i.e. patented with any changes you want to do with requirements of use of software).
so there it is, I am wanting to help push this awsome software to any and all other electric markers. I just need the help of everyone to make this happen.
-Chris
Bill of requirments on donor boards:
It must be a spare or dead board and can not come from a working marker. I dont want anybody putting a marker into "decomission mode" over this project. and i have to be able to keep the board.
List of boards being worked on and who sent them:
- Tribal board from "Ratt"
- Hyperframe board from "BigEvil"
- Fokus board from "hitech"
- Tippmann X7 board from "Swamp Thing"
- Viking board from "fsrxc1"
- GZ Intitmidator board from "211"
- Shocker SFT Board from "Deathss"
- Ion Board from "Deathss"
- Impulse Board from "Deathss"
But to the point of this thread. Now that i have completed the new Emag board, i am looking for the next board to do. I have been working on repairing a handful of hyperframe boards and have run into the problem with one board having the main chip fried. So without having a programmer/software for the chip (and because i have 500 Atmel chips in stock), i got to thinking. Why not bring Xmod to hyperframes and any other possible marker out there.
With that said, i know many of you have the Xmod programmers laying around collecting dust.....while you have other electrical markers laying around needing some nice new software. So I would like to ask all that are reading this to post some markers that Xmod would be greatly wanted for. Now dont forget old markers like B2K's and even rain makers! Anything running off an electric board i can make happen.
Now with that said, i want to openly ask LorneCash for help on this on this (since i cant get ahold of him privatly). I know you want to get the rest of your programmers sold and earn a bit more on your awsome software. So would you be willing to help change the software to work for 12 and 9 volts systems and help with any questions i might have with the software technically? this would of course give you the chance to get your code protected and safe like you really want (i.e. patented with any changes you want to do with requirements of use of software).
so there it is, I am wanting to help push this awsome software to any and all other electric markers. I just need the help of everyone to make this happen.
-Chris
Bill of requirments on donor boards:
It must be a spare or dead board and can not come from a working marker. I dont want anybody putting a marker into "decomission mode" over this project. and i have to be able to keep the board.
List of boards being worked on and who sent them:
- Tribal board from "Ratt"
- Hyperframe board from "BigEvil"
- Fokus board from "hitech"
- Tippmann X7 board from "Swamp Thing"
- Viking board from "fsrxc1"
- GZ Intitmidator board from "211"
- Shocker SFT Board from "Deathss"
- Ion Board from "Deathss"
- Impulse Board from "Deathss"
Comment