What tank/reg do you use for Xvalve mag

[ninjapaintball]

How do you do that ?

remove all air
remove 3 bonnet screws
remove bonnet
take out all the silver flat shims - not the curved springs
reassemble

[going_home]

with any of the on/off asa styles you should ste the pro v2 to 450 becuase fo the added volume of air to open it. with the lower pressure it will be easy to use the lv1

How do you do that ?

[ninjapaintball]

Unless you want to use the same bottle with mag as well.

correct and sorry!

[Laku]

with any of the on/off asa styles you should ste the pro v2 to 450 becuase fo the added volume of air to open it. with the lower pressure it will be easy to use the lv1

Unless you want to use the same bottle with mag as well.

[ninjapaintball]

with any of the on/off asa styles you should ste the pro v2 to 450 becuase fo the added volume of air to open it. with the lower pressure it will be easy to use the lv1

[ninjapaintball]

sent a pm back and got busy last nite, sorry.

[Laku]

one Pro V2 (which doesnt play nice at all with the POPS on the LV1).

Is it because too much resistance due to the bigger surface area of the ball valve?
Just curious cause I have v1 for my geo3

[going_home]

4 tanks (2 too many) all Ninja, one SHP first run, one SLP pro v1, one standard ninja, one Pro V2 (which doesnt play nice at all with the POPS on the LV1).

[Grelvire]

An Armageddon you can crank to 1200, and most of the orings are the same that the automag valves take

[zondo]

I'm running an original Ninja 68/45 with enough shims to get to 850-900 and no drop off. Just got my tanks re-hydro'd (thanks again, Ninja) so I'm back in the game!

[DarkApollo]

Ninja, I sent you a PM with my sob-story.

I thought it was odd too and I suspected the disks were bad, but a disk out of the same box has been on a different reg and has not failed. One is also installed on my MaxFLO and has held for 2 years now.

[ninjapaintball]

for the high side burst disk to pop so rare! for you to go thru so many is very, very odd.

can i call you or discuss this with you? it may be a different issue that can be solved.

[DarkApollo]

SmartParts 4500 MaxFLO... My Ninja reg keeps blowing the high-side burst disk. I bought it new and it has been nothing but problems since day 1.. It has gone through no less than 5 high side burst disks (the 7.5k ones) and it never matters the tank pressure. It is the ONLY reg that has ever given me this issue. Dont get me wrong, I have used other Ninja regs on other tanks and had 0 issue. In fact I have a Ninja on my GF's peanut tank because I like their regs. Maybe I got a bum one, I do not know.
That same tank is attached to my MaxFLO now and for the past two years it has caused me no issue. :shrug:

[Konigballer]

Performance with each tank reg/valve combo will be different for everyone's mag. I like running my classic RT's on a Ninja SHP tank set to 950psi. Neither will actually RT at that input pressure, but the trigger is so bouncy that it makes it easy to hit a decent bps even on a single trigger Benchmark frame. My field has a pretty strict ROF cap of 10 or 11bps, so it's not hard to stay competitive with electros, and not attract unwanted attention.

I used to run a Gen 2 SP MaxFlo adjustable reg on my RT valved Minimag, and that was a quality reg with a fantastic re-charge rate that would make any mag RT easily. It was just so large and fugly I got tired of it and went back to screw in tanks.

[RT Lover]

It's kind of funny/sad, the easy adjustment regs don't move easily from one marker to another, unless they are basically the same setup.

Use a dove tail or they make mounts u pull the pin u slide the tank off...