Does anyone here..................................

[AcemanPB]

i run 20oz with anti-siphon + expansion chamber, no problems so far

my field has nitrogen now so i will probably get a nitro tank soon

[AcemanPB]

oh on a side note someone else at my field was using co2 on his mag (co2 was under trigger and ran straight to the gun from) his mag would not work at all it had all kind of problems

[Army]

Sam, only the RT/ReTro valves should not be used with Co2. The Classic will run fine on juice, and was designed originally around Co2.

The RT recharge rate is so high, liquid Co2 has not time to expand completely and will be sucked into the valve.

[Jonno06]

nope,i only run nitro into my gun....i would NEVER run it on CO2...not my baby

[Paintballer86]

I am all about nitro, nothing but sweet sweet nectar for my baby (Emag)

[KyleOx1]

Ok, well the only place to get n2 fills is my field and its like hour to hour and a half away....and if i do go, then i cant practice/shoot around @ home and get a little better, so im going to have to use co2......
So ill take off the gas-thru on the TKO POWERFEED MAG that im getting, and add a xchamber or a palmer stabilizer(which should i? xchamber or palmer?)
and i guess the tko mag comes with a vertical adapter...
My questions:
Does the gas-thru just unscrew?


IF i hooked a male palmer stabilizer to the vertical adapter, would it be just like the gas-thru stock....i run a macroline to the bottom of the stabilizer, and it goes out the top at the vertical adapter or would i have to do a bunch of adjustments?(same question if i were to install an xchamber)

Ofcourse i would get an ansti-siphoned co2 as well, if i had the palmer stabilizer and an anti-siphoned co2, would my gun be consistant?

If you havent seen a palmer stabilizer there pretty much the best CO2 tolarant reg available...
www.palmer-pursuit.com < go there and click stabilizers

[theraidenproject]

I have never run co2 on my classic mag. Never will.

[KyleOx1]

I like your sig, to finish the joe dirt part off
the guys like
"let me ask u something, doesn your mother sew? BAM! well get her to sew dat!"
lol

[Army]

Your Classic should have a screw through the body rail that is holding the gas-through. Remove the valve, then body, the screw should be visible now.

A Palmers Stabilizer is an excellent alternative to an expando. The Stab is designed to help keep out liquid, and does a very good job of it. That and an anti-syphon should do you OK.

[KyleOx1]

its not going to be a classic, IM ORDERING IT and its a tko powerfeed mag

[Magluvr]

I run on CO2 and my gun runs like a charm. It has none of the problems some people associate with CO2. But it could be that I have the minimag with a Palmer Stabilizer in the vertical mount. It blocks ALL the liquid so even when I shoot 15 round bursts my mag valve/reg hasn't even begun to get cool. (It stays the same temp all the time)

[KyleOx1]

nice, how did u install it?
take off gas-thru(if it had it) and just put the palmer in?

[pumpamatic]

Honestly, I run less of a fancy setup on CO2 than most of you do, and I've only once had a freeze-up because I stupidly pointed the gun towards the ground and emptied over half a 12 oz in one dry firing. All I have is a 6 stage expansion chamber and a slightly as in about 5 degrees angled bottomline and a 20 oz and 12. Oh and one another time it was about 10 degrees out and I dropped a few drops of oil in the gun on the field and gassed up with co2, bolt stuck and leaked so I changed to what little nitro I had left and later changed back to co2 and shot about 250 rounds the rest of the day, my only problem was I had about half the gas efficiency I normally get. 2 weeks later in about 30 degree weather I shot around 300 with 2 breaks, 1 of them down the barrel. I only shoot nitro at fields that can fill it, I only get maybe 400 shots out of it, but hopefully can get a better tank this summer.

[KyleOx1]

damn, well i cant wait til i get my gun!

[Croix71]

I used to use CO2 but once I've crossed over to compressed air I've never gone back.