loctite

[andrew51]

how long does it take for that stuff to dry?

[paintbattler]

i wouldnt use it..im not a fan of it

[Schnitzel]

10-15 minutes

[andrew51]

jeez, i put the stuff on 4 hours ago and it isnt dry yet!!!mabey its the heat

[LawFox32]

but it in the fridge it will dry a lot quicker, cuz heat is what makes it soft and wet/undry, I guess, but hey it makes a seal w/in a few minutes, cuz I had a leak on my set-up one time and it was on a fitting or something and I just put it on and then turned on the gas and it was still leakin so I tapped it a few times and turned the fitting in a lil more and it sealed right up

[MikeCouves]

Drying? Just use silicone tape, teflon tape. Works just as good as doesn't need to dry.

[StuDawggie]

Originally posted by andrew51
jeez, i put the stuff on 4 hours ago and it isnt dry yet!!!mabey its the heat

Depending on where you're at, it could be the humidity...

[Spaceman613]

well, if you use a lot it will take a while, you dont need much. What type did you use? most loctite is good in about an hour, and full cure is within 24. Use blue for most things, and purple for small screws. DO NOT use red unless you want to get smacked. Green is good, but a lil goes a LONG way.

I use it on everything, but you have to select the correct type for your application. What did you use it on, and what type?

[damageinc54]

God I just love to read loctite threads!!!!! Loctite makes a primer that I highly suggest using. It helps prepare the part and it makes it dry much faster. You have left out many important facts such as what you are trying to loctite and which type you used. I am a Machinist and I work with the loctite every day so I can help you out.

[BlackVCG]

Keep in mind Loctite makes a wide array of products which are NOT all thread locking agents. If you're trying to seal an air line, use 592 (personal favorite) or 545 (for all the other AGD techs).

[sniper1rfa]

actually, the only thing that keeps loc-tite soft is air. it dries with lack of air. therefore, if your using it on a fitting, it will dry faster if you tighten the fitting down good.

red loc-tite is good for many things that will never need adjusting or will never need to be taken apart. maybe sealing half of a hole after drilling a manifold .

blue is good multi purpose loctite for screw over maybe a #8 or so.

purple is good multi purpose thread-locker for under a #8

green is just sketchy.

[Temo Vryce]

You'll want to let it sit for 24 hrs before using the item in question. As for Teflon tape, it doesn't have the PSI rating that Loctite does. I think it's less than 200 PSI. Do you really want to put that on your reg for your 4500 PSI N2 bottle?

[Thordic]

Yeah, Loctite is an Anaerobic sealant. It dries in the absense of air, and stays a liquid when in contact with air. Makes it good for paintball because if any gets inside your gun, it shouldnt dry into little clumps.

I use Loctite 545 personally. It goes on a reddish purple, and dries to a dark red. (Not to be confused with the red loctite threadlocker, which goes on bright red and dries bright red).

545 is LocTite's pneumatic sealant. It'll work on threads for systems up to 10,000 PSI or somewhere in that range, I believe. It's more than enough to seal paintball threads. It also doesn't lock the threads, so when you need to take that fitting off all it takes is an adjustable wrench and a tad of torque. Red or Blue loctite, or any other kind for that matter, besides being hard to remove (which will probably damage threads), may not hold up to pressure as well. I usually let it dry for 24 hours on something like a fill nipple or your tanks HP guage. I'll give anything else a few hours. Note that the stuff that isn't inside the threads won't dry. You will get a little "puddle" that gets forced out when you screw the fitting in right around the fitting. Just wipe that off with a rag or something.

[MikeCouves]

Actually I have been using Teflon Tape for years now and so has everyone else that I know around here and it has NEVER failed me once. And it's dirt cheap too, you can pick it up for like 50 cents.

[legion]

The only problem with using teflon tape is you have to make sure you know what you're doing when you put it on. If you put it on improperly it could shred into your air system, and mess up the internals on valving and whatever. For loctite, that isnt a concern (though you should still know what you're doing when you use it). The other thing is, depending on what type of marker you're using, applying teflon tape to any of the airfittings can void your warranty (i know this is true on impulses, dont know which other guns)

Legion