Checkout the NEW Xtreme Manual Online!!!!

[SeeK]

http://www.scottplayer.com/valve.html

This page should have some of the diagrams reversed so the pictures are consistenly oriented. It gets confusing to distinguish the parts because the picture is facing to the left and the diagrams to the right.

[Evil Bob]

The drop down contents menu has the pages jumbled, and on some pages out of order from the previous page. They should be numbered and highlight the current page your on.

-Evil Bob

[kilaueakid]

Under the section titled "Valve" where it describes level 10 and the carriers and lenghts. I thought the carriers differed in ID size in the reccessed area that holds the o-ring, making a more snug fit the lower the number or loose fit the higher the number. I was not aware that they were different in lenght.

kila

[Cristobal]

I would also add a note about Radio Shack (and other electronics stores) selling power converters which would allow the user to charge their Emag from a wall outlet.

[ben_JD]

Proposed edits to the general page

I have attached a redline for this page. It includes some revision suggestions in a format widely used in document negotiation. For the most part, the site is well-organized, it just needs a little polish.

[Edit: It appears that I cannot post an Acrobat file, so I will slump quietly back to the corner from which I came.]

[seizurepants]

where can i get an emag extreme body

[SeeK]

Sprawls Farm, West Bergholt, Colchester, Essex, CO6 3DN, U.K.
Office hours: 9:30am-5:30 pm (GMT) M - F
Office Phone: +44 (1206)240831 Office Fax: +44 (1206)240821

http://www.airgun.com/Europe

[tomcat]

User guide changes

thanks for the help guys. I have made most of the changes you suggested. hope they meet with your approval.

I am still working on correct part numbers and part identification, so bear with me on that one.

I would appreciate if you can go through again and find any more mistakes or make recommendations.

Nothing but the best for AGD users :)

Also e-mail me any pdf's or other info that you can't post..to [email protected].

Thanks again :)

[riooso]

Excellent work! I am always amazed when I see what can be done with graphics today. The manual is really an nice body of work and I am sure that it took you a tremendous amount of time. Good job!

R

[DarkPhoenix]

I have a question concerning the different firing modes. As listed in the Extreme E-mag manual, the E-mag has three modes of fire Manual, Hybrid and Electonic. The Extreme manual also shows the selector switch for these modes. My question is the third selector switch position (hybrid) only specific to the Extreme E-mag? As an owner of an E-mag, the third position (as pictured, in the extreme manual) serves no additional function (on my gun), as my gun fires in digital mode in that position. To attain hybrid mode on my E-mag, I remove the battery pin and have the selector switch in the manual position.

[paintbattler]

Originally posted by xmetal2001
If its going to stay as a online manual, then you need some navigation buttons at the bottom, the dropdown in a pain.

yeah it deffinately does need one...it gets on my nerves scrolling through

[riooso]

Hello Dark. I have seen an American version of the Xtreme and the manual is correct. I have the Euro version of the Xtreme and it is set up like the standard Emag. I did have a chance to handle it but could not tell if the shot
clock and the rest would work in "Manual" mode. The owner said that it did but I did not check it.

R

[DarkPhoenix]

So I take it by the above post the US version of the Extreme E-mag will incorporate a 3-position switch which will shut off the battery in mechanical mode and energize the electronics for the hybrid and electro modes?

[riooso]

I saw a switch on the right side of the American Extreme and I was told that
in the "Manual" mode basically everything except the ACE and Trigger worked. The rest of the modes are same as the standard Emag. I can tell you this, no matter what edition you get this marker absolutely "Rocks"

R

[openboater]

Just got my Xmag back from AGD with upgrade to 2.1 software. ACE can only be set to a 0 or 1. No 2 is available as the manual states.