I say go all the way to just below the hole. What do you think?
Left is stock body and right is cut down and lowered...
Left is stock body and right is cut down and lowered...
-
Last edited by cphilip; 09-28-2002, 06:55 PM. -
Hole
at the hole -
Not sure what you are meaning. its "at" the hole now...explain?Comment
-
Re: Go Lower you think?
I agree.Originally posted by cphilip
I say go all the way to just below the hole. What do you think?
www.ShartleyCustoms.com
Custom Paintball Products and Accessories
CLICK HERE to Check out our PDU SERIES GEAR!
its more like a paper cut that has primadonna's yelling murder... - GlickmanComment
-
LOWER!
Christian, and proud of it.
My setup, built by Tunaman:
http://www.automags.org/forums/showt...threadid=50949
Good Traders: Tunaman, dnm5d, vf-xx, cphilip
FOR SALE:
One 'cocker barrel and a pre-2k APBBOLTS anti-chop bolt. PM for info.Comment
-
what do you do to lower it like that?Comment
-
It is desoldered and then the tube is cut down and its resoldered on there. Silver Solder I think. BradAGD is doing 6 of these for me. Some will be available for sale by the way.Comment
-
straight to the body
E-magnum lx warped halob
z-grip ptp micromag
ptp f\x sleeper cocker
my emag hiku
cockers shoot farther
ouch ouch ouch ok im out
damn an other emagComment
-
i say get lower if it wont affect anythingSomeone took away my cool sig. *cough*mod*cough*Comment
-
Well..i'd say make it so that the amount below and above the hole is the same for uniformity..and if i could get one in Teflon i'd take it in a heartbeat..Comment
-
I WANT ONE !!! Please... I beg of you... I want a vert feed body for my e-mag... Lemme know the minute the are for sale.. Thanks
Jim GComment
-
Well Dirty... there is one black body out of the six that is there. But I fear the black is going to be messed up by the soldering and will need to be stripped or coated or something. But lets wait and see. It was a messup on my order but I figured lets see how it goes so he is going to try it. We can always polish it out too if need be. Or I may send it out to be coated or something.
When they are available they will be in a post in Classifieds for sale but you can email me in the mean time if you are interested. One is presold. One I am keeping and I think Tunaman is getting one too for himself but not certain about that. He has first shot at one anyway. But there will be at least three including the black one if someone else wants it. I will keep it for mine if not.
However...
I do not want to turn this into a classified post now. All I realy was looking for here was some other opinions. I am leaning towords just below the hole where the bottom lip of the "Bell" would be.Comment
-
i agree man take em as low as you can without damaging performance.Oh yeah I got to use your old emag today thanks to Blazestorm and boy did it rock.Good Traders:JoeyJoe367, Blazestorm213, RetardedRiceBowl, rsadich,PaInTbALL zAcH, jwyke. John Dresser, Xas, Darrikws,whydoineedausername
Splat Attack Revenge V2 LE FS
Conquest FSComment
-
Well...good performance in this case is designed for use with the Halo B and lvl 10. Should not be an issue but might be with a regular hopper but maybe not so much with at least the lvl 10 in there. But that is what we are designing these to be used with. Halo B's which seem to like a short feed stack. In fact they work better with them.Comment
-
go lower phil, do you only have that one done right now?Comment
Comment