Alright, one awsome WC product (really!)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bofh
    Waldorf, the Heckler
    • Jul 2001
    • 1248

    #16
    Originally posted by lala
    could't that be the camrera worping it and like the flash mabye and becouse its so close.
    Yeah, it looks like an optical effect, you'll also notice the table edge is also warped.

    It might be tapered, but not anywhere near as much as it looks in the picture.
    Shaun Nelson --- old, fat, slow.... did I mention lazy? I ate all the pies
    I disable .signatures Apparently you do not.

    Comment

    • SlartyBartFast
      The Flying Scotsman
      • Jun 2002
      • 2940

      #17
      UMmmmm....

      The OUTSIDE might be tapered, but I think it's a little unlikely anyone would create a barrel with a tapered INSIDE.

      Comment

      • RetroEclipseMan
        AO's Future Game Artist
        • Jun 2002
        • 1386

        #18
        They look pretty good to me.When AGD comes out with the aluminum bodies for the standard mag I'll be in need of a barrel kit to go along with it and for the price compared to the Freak or J&J it doesn't seem too bad.Hopefully it'll be everything it's hyped up to be.
        Good Traders:JoeyJoe367, Blazestorm213, RetardedRiceBowl, rsadich,PaInTbALL zAcH, jwyke. John Dresser, Xas, Darrikws,whydoineedausername

        Splat Attack Revenge V2 LE FS

        Conquest FS

        Comment

        • TRIAD
          Registered User
          • Jun 2002
          • 889

          #19
          They say they are built to have tolerences within .0007 of an inch. Now, you're talking about barrel sizes of .679-.695, or so. Those're just guesses, but it doesn't really matter. So, let's say you have in your hand the .685 and the .687.

          Now, the tolerence could be either accuracy or precision, accuracy being how close it is to what it was intended to be, and precision being how close two barrels of the same bore are to eachother. Tolerence is a loose word.

          Now, let's assume they mean accuracy, so that means a .685 could be .0007 inches up or down. That means it could be anwhere from .6843 to .6857. Also, the .687 could be anywhere from .6863 to .6877. That means the ".685" bore size could be as close as .0006 to the ".687" bore size (.6857 to .6863). So, that means that your different bores are in reality .0006 inches apart, rather than the advertised .002 inches apart. This is a HUGE difference.

          The same problem would arise with a precision of .0007 inches.

          If BOTH the accuracy AND precision can be within .0007, then there's no point in owning the kit. Because this would mean that it could be up or down .0014, a .685 barrel could be anywhere from .6836 to .6864 and a .687 could be anywhere from .6856 to .6884. This means the bigger ".687" bore could actually be SMALLER than the ".685" bore.

          Tolerences to .0007 inches are truly nothing to brag about. Without further information, there is no way I will even consider purchasing this barrel kit.
          Last edited by TRIAD; 10-24-2002, 03:16 PM.
          Christian, and proud of it.

          My setup, built by Tunaman:

          http://www.automags.org/forums/showt...threadid=50949

          Good Traders: Tunaman, dnm5d, vf-xx, cphilip

          FOR SALE:
          One 'cocker barrel and a pre-2k APBBOLTS anti-chop bolt. PM for info.

          Comment

          • TRIAD
            Registered User
            • Jun 2002
            • 889

            #20
            What's up with their website, I can't get in, it's just a screen with a picture. Any other thoughts on the barrels? Anybody use them?
            Christian, and proud of it.

            My setup, built by Tunaman:

            http://www.automags.org/forums/showt...threadid=50949

            Good Traders: Tunaman, dnm5d, vf-xx, cphilip

            FOR SALE:
            One 'cocker barrel and a pre-2k APBBOLTS anti-chop bolt. PM for info.

            Comment

            Working...