My CnC.........well almost!

[riceetr69]

did you get the new rail converted from AGD. does it come with ACE?

[snakestang]

VERY nice job. As for powder coat I say red to black fade, silver to red fade. Looks like they took off a ton on that rail.

If you need a scale you can always take it to the post office. They have one in the lobby for customer use any time you want. Its probably going to be very accurate as well.

[Load SM5]

Walk into a post office with a gun shaped item?......

[pito189]

Originally posted by riceetr69
did you get the new rail converted from AGD. does it come with ACE?

No, it is just the stock rail that got the piss milled out of it. Althought it would be cool it does not have the ACE it still just the normal rail just milled.

[pito189]

Originally posted by Load SM5
Walk into a post office with a gun shaped item?......

I could just weigh the rail and I think I would be safe there.

[riceetr69]

where did u get it milled? how long does it take to get your emag back from the company?

[pito189]

I can give you the person's information if you would like it just drop me a pm or e-mail.

I will just say it took a lot longer for shipping then it takes for him to actually finish the milling.

[riceetr69]

Thanks

[ah137]

Looks great!! If I have a standard emag (sold and now own a micro emag) I would have done the same thing, Plus this

-Cut the main body back
-get close or match the angle of the main body cut to the rail cut.

- cut the back of the rail down also

hope that makes cents

My mirco is gettin milled right now

Later Hills

[pito189]

Originally posted by ah137
Looks great!! If I have a standard emag (sold and now own a micro emag) I would have done the same thing, Plus this

-Cut the main body back
-get close or match the angle of the main body cut to the rail cut.

- cut the back of the rail down also

hope that makes cents

My mirco is gettin milled right now

Later Hills

I am considering it, I'm just not sure of what to cut the body with? Also how would i smooth the edges after the cut?

[Seabaas]

nice body, I'm considering having that done to my emag body too just to lighten the gun up a little and make it look a little trimmed down. However I'm not quite sure what to do about the body. I have a left pf like yours pictured there yet I want to put a warp on the left side. I really don't want to run the hose around the side of the gun, but I might have to for now. I would just buy a left warp body but the AGD store says they are sold out and have been since early this year. Eventually I'd like to have everything upgraded into a C&C xtreme body so I'm wondering if I should even have something like this done. Also my long powerfeed plug for the warp, I was looking at the pic of yours and it covers half the opening, mine doesnt come down that far and there is a small lip or gap between the plug where the tube meets the breech. I'm wondering if I'm going to have to cut down the power feed tube a little to make that flush. It's probably off about a quarter of an inch or so. - Seabaas

[Seabaas]

Darn I didn't have a pic of my gun with me I'm at work so I took yours and trying to show where my powerfeed plug is stopping at, anyone know if I'm going to have to cut down the powerfeed neck or not? - Seabaas

[pito189]

I would probaly call AGD and get another plug before you started cutting on your body. Try to trade your body for an HR. Then you can just have the hose coming out of the bottom of the powerfeed. I don't want to get the warp right, because then if the warp goes down your kinda screwed.

I do want to get a no rise body eventually.

[p8ntballa]

I got mine back today. The Emag before I had it milled was 3 pounds 4 ounces(with the classic mag body) and I will tell you what it weighs now on Saturday.

[Skoad]

tell me sometihng, did you polish the freak tip by yourself?
i can't find a freak tip that is polished, alls i cna find is anno'd silver