Is this setup possible???

[Grayso]

I am getting a micromag and I want to upgrade it. I need to know if my upgrades will fit onto the micromag. I am pretty sure a Z-Grip will fit. Next, I want a Vertical Bottle Adaptor, and a gas thru grip. Will it fit by itself, or do i have to buy a foregrip extender? If so, does any automag grip extender work on the micromag, or will I have to buy a special kind? I also want a warp feed, but I know it will work on a micromag. If any of the other stuff will not work, let me know. I am going to order all the stuff in about a week. I want to make sure it will actually fit together, before I pay for it. Thanks.

[EsPo]

the warp will work fine.. if you buy it used make sure that they include the 90* adapter, unless you want a hose going over the top of your gun..kind of ruins the purpose of warp.

[Grayso]

I know the warp will work. But what about the Z-Grip, Grip Extender, and Vert. Bottle Adaptor. Will they fit on a Micromag?

[Quiet]

The z-grip will work but you would have to have a foregrip extender for the vert. ASA and foregrip to fit. I don't know if the Kapp one fits a micromag, it's the only one I've seen for a mag.

[Grayso]

Ok, thanks. Now all I need to know is whether or not a forgrip extender will fit on an micromag. Does anyone know of any extenders other than the kapp one? Its the only one I've seen too.

[jah871]

you will also have to cut the extender to allow it to fit because the trigger guard will hit it.

[Riot[Z-Grip]]

I found a warp too awkward with my z-grip. You'll want to offset your tank with a z-grip so that your wrist doesn't hit it. Depending on how you do this, you will need to cut a new warp bracket so it will clear the tank. This left my setup ungainly huge to the left. I suppose you could put the warp on the right (if you are a lefty, then just switch everything around), but I think having a warp on one side and a tank on the other would also be very awkward, not to mention not a tight setup at all.

-Riot

[athomas]

If you plan on using the Z-grip, use a bottom line (dick bill) typ ASA and a short tank. That will keep the tank away from your wrist and make a very comfortable setup. The air line will have to go directly from the ASA to the valve though.

As far as I know there isn't a forgrip extender for the micromag. You may be able to get one custom made. Without the forgrip extender or an angled ASA, the gas through grip will not fit with the Z-grip.

The warp setup will work fine if you use the bottom line ASA setup. The warp will act as a front grip as well.

[BTAutoMag]

http://www.automags.org/resource/gallery/mag/mag24.shtml

i think this is what youre looking for.

[srrdude]

Well i have a z and a warp on my rt. I dont use and offset drop. I use the standard flatline drop. I dont find my warp awkward either, tho i did need to get an extra hole milled in the mounting plate.

[Grayso]

If i cut the trigger gaurd off, will a gas thru grip clear the bottom of the z-grip? If it will, then I'll just do that, and the gas-thru will basically replace the trigger gaurd.

[BTAutoMag]

dont cut the zgrip what every you do. I beg of you

[srrdude]

you cut the z ill cut ur throat. Not really, but dont harm that precious work or art.

[Grayso]

What's wrong with cutting the trigger gaurd off? It's just the trigger gaurd, not the whole frame. Will a gas thru grip fit on it if I do cut it off?

[Peach]

NOOOOOOOOOO DON'T CUT!!! GET THE EXTENDER!!!

PS: Do you really want hate mail for the rest of your life? If the answer is NO, then don't cut it!!! AHH The thought even hurts...