Need hard tech questons

[ezrunner]

2 things

first there is the inverse output of reg systems, but basically you want to have 2 regs and the inline (2nd) reg should have a 150 - 300 psi gradient or difference in input and output pressures.


As far at pressure behind a valve goes, you hit the valve from one side with a hammer to open it.

The pressure on the other side is the combination of 2 things, spring pressure and air pressure.

When the air pressure reaches a certain point, it begins to make the valve open less.

-rob

[Ghost Stalker]

Here is one for him. There is a spyder compact that when you pull the trigger it doesnt shoot every time. You have to pull the trigger a few tiomes for it to shoot. But when you pull the striker knob back about a millimeter it will cock and shoot. So you have tried a new sear, striker, o-rings, and even new springs in the frame and the gun itself. But it still doesnt fire every time you shoot. Basically replacing everything in the gun.

Answer: There is a pin in the frame that the stiker hits. If the gun is old or has just been used a whole lot the pin will wear, resulting in the above problem. So you have to flip the pin around or replace it. It is a hard piece to see unless you get a flash light and really look hard. Believe me.

[No sKiLLz]

Re: 2 things

Originally posted by ezrunner
first there is the inverse output of reg systems, but basically you want to have 2 regs and the inline (2nd) reg should have a 150 - 300 psi gradient or difference in input and output pressures.

As far at pressure behind a valve goes, you hit the valve from one side with a hammer to open it.

The pressure on the other side is the combination of 2 things, spring pressure and air pressure.

When the air pressure reaches a certain point, it begins to make the valve open less.

-rob

I think I'm not understanding. Starting with a Matrix with a HP preset tank, the gauge on the inline output reads 210 PSI and shoots 300FPS. Now switch the HP preset with a LP preset, and retune the marker over a chrono to 300fps again. Checking the gauge it reads 190. The only difference being the tank presets. How?

[Jeff_PbDaddy]

Question: What was the name of Sky King's airplaine?

Ansewr: Songbird.

[bryceeden]

Thanks for the paintball related responses, keep them coming. I could use something hard about a mag, because he is clueless about mags(maybe explain the compleat steps(what the valve does not what the user does) used in an X-valves mags firing) I don't realy know anything beond the basics, so if anyone could help me out I would apreshiate it.

[ezrunner]

Mags

Timing issues:

What role does the power tube spacer play in the timing of a mag?

(it adjusts at which point in the bolt travel the air begins to be released)

[dinger]

how do you adjust the pull on a spyder imagine?


A: theres a screw inside the frame on the trigger. unscrewing it makes the pull shorter because it hits this bar in the body.


you wouldn't believe how long it took me to figure that out lolol

[Octavian]

how do i

how do i put an impulse i frame on a bob long defient?

[bryceeden]

I forgot to say he runs a paintball shop, and is an almost semi-decent airsmith. So the questions need to be extreamly tricky(I don't know if he'll know the timing on the mag one)

[AGD]

It's simple, ask him how an O-ring works. If he gives you a one sentence answer he is wrong.

AGD

[Dayspring]

HAHAHAHA!

And there it is.

[bryceeden]

Thanks Tom, I bet that will beat him. Could you give me the answer, I would use the one sentance answer. If I don't know the answer he probably won't exept defeat.

[Dayspring]

Do you have the hour for Tom to explain it?

He did it at the Megameet. He did it at IAO.

The Oring Talk will FRY your brain.

He'll give you information. You'll give him what you think is the right answer. He'll look at you and go "Are you sure?"

At this point, you question every choice you've ever made.

[bryceeden]

Could you summerize it so I can prove Him(Dale) wrong.

[AGD]

Draw a circle on some paper, at the top-bottom-left-right put the numbers 1 throug 4. North would be 1 south would be 2 etc.

Ask him which numbers on an oring are the sealing points. The correct answer is "three but it depends". If he says two or cant explain three he is wrong.

AGD