how do I change goggle lenses?

[penguinpunk555]

Help me!

They need it by now.

[Stewylouie]

You should start first by telling us what kind of goggles you have.

[RenagadeOfFunk]

...you are dumb...



...what goggle system?...

[the larch]

well, if they are dye invisions, you'll need a jackhammer........ No, really, assuming you don't want to keep the old lenses, I stick my dyes in REALLY HOT water. that makes it easier to get the old lenses out. and the new ones in (don't immerse the new lenses in hot water). don't sut me if your mask melts.

[penguinpunk555]

I kept reminding myslef to tell you guys what type of goggle what type of goggle while I was searching. Stupid low attention span.




Pro-flex

[Bad_Dog]

take the goggle part off of the mask part...

then the rubber edge comes off the lenses....

just mess with them untill they come out... you cant ruin a proflex

[Chipper]

1st time on my proflex was a butt but ( ) after that it got slightly easier. But you do pretty much need a jackhammer.

[JrnyFan1985]

well, if they are dye invisions, you'll need a jackhammer........ No, really, assuming you don't want to keep the old lenses, I stick my dyes in REALLY HOT water. that makes it easier to get the old lenses out. and the new ones in (don't immerse the new lenses in hot water). don't sut me if your mask melts.

gotta love the vforce system, and now the JT mask copying them like... well you know.

[penguinpunk555]

u guys arnt helping....

[Stewylouie]

Seperate the mask from the goggle frame.
The mask connects to the bottom of the frame.
Take off the visor, if you have, it pulls away from the top of the frame.
Peal the frame away from the google lens.
You'll see three notches on top and four on the bottom where the lens attaches to the frame.
No trick here, just pull, if this is the first time, it will be very hard.
After its out, put the new lens in by reversing the process.
Push the lens into the frame first around the nose area, where you'll see two notchs.
After their in, slide the other two bottom notchs in.
Then work the lens into the top, start at the sides first then the center notch.
YES IT WILL BE VERY HARD, there's no way around it.
Be patient and keep working the lens in.
It'll eventually go in.
Yes, it'll take 15 minutes and your fingers will hurt.
If its tough, your not doing anything wrong, just keep working at it.

[rkjunior303]

couldnt you heat up the goggle with a hair dryer or a heat gun?

[JrnyFan1985]

yeah with a JT, it's crazy mad hard. When you take the lense out of the holding place, work from one side of the mask, i.e. put the lense in the right side or left side FIRST, then work your way from the bottom of the mask to the other side. as soon as you snap in all the parts where the lenses go in on the bottom portion, the rest should be a snap. MAKE SURE YOU SNAP IN THE NOSE PART OF THE LENSE it is really difficult but it just takes time.

[Enemy]

ok easiest way to do this is follow the directions two posts above me...to remove it is just pull on the top of the mask as hard as you can then the lense.. getting it back it is just as hard the way i found works the best is to on the notches start bye pushing one side in the slide your finger firmly accross to force the other side over.. dont be surprised if your first time takes a while but the notches will wear a little so it will be easier in the future... thats about it.

[edweird]

if its an invision I suggest starting out with 3 or 4 hefty painkillers cause 20 minutes into pulling that damn thing apart your hands are going to need it!

or just toss it and get a profiler... hands down that system that V-Force uses is the best evar!

pull the clips, pop the lens, peel the plastic(hardest part of it!) then clip it in... done and done

[Head knight of Ni]

hands down that system that V-Force uses is the best evar!

I agree