Fireblade for mechs?

[RRfireblade]

Uhm........yeah, that's way I said that.

[personman]

Fireblade, just to let you know, if you made a small run of those mech triggers I would most likely take one in black
I screwed up my trigger with a dremel.. its all sloppy now.. don't ask, it was a stupid mistake, but if you made some of those triggers and a the price was right, I'd probably take one Assuming they fit in a y grip.
I'm too lazy to buy another AGD trigger and get it annoed black again.

I'm curious as to why the medusa was never released and/or advertised? It looked pretty promising.

[trains are bad]

Yeah dude, we're up to 2. What would it cost for a mech fireblade?

[CoolHand]

I have been considering a replacement trigger for the I/Y frames.

What do you guys think (that's a collect AO type "you guys")?

What would the upper limit that you'd pay for one? (so I can tell if its worth doing or not )

If this gets enough interest, I don't see why we couldn't make them a part of our growing product line.

Have at it guys, let the feedback flow!

[RRfireblade]

Send me your Y frame (since I don't have on handy) and I'll do something special for you,that goes for you too Trains.

The deal is, I'm not really set up for production Believe it or not, we have over 1/2 a million $$ in CNC machines at our production facility running 2 shifts and it's so backed up I'm lucky if I could get 5 mins of machine time in there a month. Everything ,pretty much, that you see from me is done on manual machines and one at a time.The first ever 'Fireblade' was made in my garage with nothing more than hand tools.

Trust me if I had direct access to those machines it might be called J-AGD. by now.

Anyway, that's also one of the reasons for alot of stuff doesn't make it into production. When you can't keep up with product that's selling off the hook,it's hard to justify machine time for items ,let's just say, are less than "In Fashion". Only so much you can do in a day.

[RRfireblade]

Or..........

What Ryan said right before me.

[CoolHand]

Or..........

What Ryan said right before me.

I gots the fast fingers.

Your CCM will go out tomorrow.

BTW, any word on that thing I asked about that one time?

If you're in need of production capacity, I got your back. Just give me a ring.

Can't let too many of those ideas you get not go into production.

[RRfireblade]

Tell me about it.

As for thet other, there are "things" in process, so I'm told ( I can give you details in private), that have to be finalize before "other" things can be considered. It's been going on now for a couple months so it should only be like another.....what 10 years? IDK.

The general consensus is that there will be definate possiblilties available for 'certian' people.

Jay.

[trains are bad]

I'd take you up on the offer if I had a spare trigger, but my yframe in particular is a little too valuable to send off. I shall try to work with the stock trigger given the tools I have. Do you think I could flatten the stock trigger out without it breaking, maybe if I heated it with a torch?

[RRfireblade]

I doubt you'll get it to bend that much with out breaking or getting badly mis-shaped.

[chairman_mao]

Along the same lines could a Fireblade be made to or will it fit a logic v1 frame?

[CoolHand]

Along the same lines could a Fireblade be made to or will it fit a logic v1 frame?

I can make a V1.1 trigger fit in a V1.0 frame.

You won't get a safety, but you will get the stylish new trigger.

A FireBlade Might fit, but it would cost you more to buy one to try than to have me put one of the V1.1 triggers in it.

However, (there's always a however) I will need you to send in your frame for me to do the machine work to make the new trigger fit.

If that's OK with you, its OK with me.

Later