SP Magic Box

**MajorDamage** · 01-07-2002, 08:22 PM

It makes your gun constantly starve, to where you get drop off real quick, and messes stuff up. It was supposed to work like a low pressure chamber, but well...dosn't. I don't even think they make them anymore.

ENDO!

**SoupRman** · 01-07-2002, 08:31 PM

it's a waste of money for whatever you payed for it. heh (don't buy it)

**OldSchoolMag** · 01-07-2002, 08:37 PM

I have a Magic Box on my 'Mag, and even though my 'Mag performs great, I still get drop off after a string of balls. Also, I asked Joe at SmartParts.com, and he sent me this e-mail to answer my question:

WHAT THE MAGIC BOX DOES IS ADD SOME EXTRA SPACE TO THE MAG WHAT THIS DOES IS LOWER HE PRESSURE THAT THE GUN IS FIRING AT IN TURN THIS ALLOWS THE GUN TO BE A BIT GENTLER ON THE BALL AS IT IS FIRED RESULTING IN LESS BALL BREAKAGE AND LESS DISTORTION ON THE PAINTBALL WHEN IT IS FIRED THIS HELPS
WITH RANGE AND ACCURACY.

thank you
joe
[email protected]
[email protected]

If anything, I break MORE than other 'Mags, and I have less range and less acuracy. I just ordered (AND IT ARRIVED TODAY! WOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOT!) my RT Pro, and I'll plan on selling my 'Mag for as much as I can get. It's a good 'gun, it works, but from shooting other 'Mags, I really haven't noticed much improvement, as I said above, but the problems don't happen that often... of course, I do use Nitrogen, and have NEVER used CO2 on it, so that may have something to do with it. But, when my 'Mag gets into its groove... ain't no stoppin' it, ya hear? If you have anymore questions, post again!
Hope this helps,
OldSchoolMag (Although I should probably change the name since I got my RT!!!)

**PaInTbALL zAcH** · 01-07-2002, 08:38 PM

at the warpig automag manual it talks about ita little

**RaV3n_Pa1ntba||** · 01-07-2002, 09:44 PM

Haha the smart parts magic joke haha that was a good one. TX I needed a laugh... well as most people say stay away from non-AGD well there are a few good companys that know what there doing and do it right... but in this case JUST STAY AWAY from the 300 dollar massacre.

Well it does bs its just as bad as a talon (not that bad but gets close) As i say stick with your stock mag valve...the reason why there are no internal upgrades (that work right) is because AGD Perfected it. Saves you money and time.

**strongboy2005** · 01-07-2002, 10:01 PM

Originally posted by RaV3n_Pa1ntba||
ANS Phase II Venturi Bolt

you have the ans bolt? how do you like it, would you recommend it?

**DrEvil** · 01-07-2002, 10:15 PM

I have an ANS Phase II bolt. and I highly recommend it. But not in your mag. use it as a paperweight. I bought my minimag used. the first thing i replaced. my gun leaked bad down the barrel burped farted shot very bad. It was quite amusing actually. All i did was replace the ANS with a superbolt. presto!!! now I have a good shootin mag.

**Butterfingers** · 01-08-2002, 08:13 AM

I agree...

Pop the foamie off, it meakes a GREAT looking paperweight...

AGD puts the best of the best in thier guns there should be no reason to upgrade. If another manufacturer claims that thiers is better 99.9999 percent of the time they are lying.

**paintballer187** · 01-08-2002, 02:56 PM

ok, thanks for the info guys. i couldn't find a pic, does anyone have one or know a link to one?

**RaV3n_Pa1ntba||** · 01-08-2002, 03:17 PM

First off ...they didnt ask you tx.

strongboy2005

I like it alot. It does everything its suppose to do ...ball breaks are cut in half...and concistensy is boosted up a tad. I can play in cold whether with normal paint cause its soft on the paint. Its eather I got a really good one or everyone else is bs'in. I highly recommend it. get yours at www.g3pb.com thats where i purchased mine...so maybe theres are special. And no i have had no problems with it ...had it for 2 years now too. Just changed foamies a couple times...which they include.

**LittMag** · 01-08-2002, 03:42 PM

Actually I have one on my minimag(the mag was given to me by my cousin who put it on), I run CO2 off of it and have not had any problems w/ breakage or shootdown... here's some pictures of it on the mag...

From Lab to Launch: How Vanessa Chan Is Training Ph.D. Engineers for Real-World Impact

http://www.seas.upenn.edu/~litton/images/paintball/littsmini.jpg

EAS5500: Applying Your Thesis to the Real World is helping Penn Engineering Ph.D. students bridge the gap between research and impact. Through industry mentorship, commercialization training, and real-world networking, students learn how to turn breakthrough technologies into solutions that reach the market.

From Lab to Launch: How Vanessa Chan Is Training Ph.D. Engineers for Real-World Impact

http://www.seas.upenn.edu/~litton/images/paintball/minivalve1.jpg

EAS5500: Applying Your Thesis to the Real World is helping Penn Engineering Ph.D. students bridge the gap between research and impact. Through industry mentorship, commercialization training, and real-world networking, students learn how to turn breakthrough technologies into solutions that reach the market.

Testing AI Against Public Health’s Existing Tools

http://www.seas.upenn.edu/~litton/images/paintball/minivalve2.jpg

Penn-led study found that AI chatbots made vaccine-hesitant parents more likely to say they would vaccinate their children against HPV, but did not outperform materials from government health agencies, whose effects also lasted longer.

Testing AI Against Public Health’s Existing Tools

http://www.seas.upenn.edu/~litton/images/paintball/minivalve3.jpg

Penn-led study found that AI chatbots made vaccine-hesitant parents more likely to say they would vaccinate their children against HPV, but did not outperform materials from government health agencies, whose effects also lasted longer.

From Lab to Launch: How Vanessa Chan Is Training Ph.D. Engineers for Real-World Impact

http://www.seas.upenn.edu/~litton/images/paintball/minivalve4.jpg

EAS5500: Applying Your Thesis to the Real World is helping Penn Engineering Ph.D. students bridge the gap between research and impact. Through industry mentorship, commercialization training, and real-world networking, students learn how to turn breakthrough technologies into solutions that reach the market.

**strongboy2005** · 01-08-2002, 08:56 PM

hmm. now i'm stuck. ok here's my situation: I want a new bolt that pretty much WILL NOT break balls. I don't mind if i can't get as good of an R.O.F. because I am a front play and i fire a max of 3 shots every time i snap shoot. I have no room for error when it comes to ball breaks up front. Now, i heard superbolts KILL paint, and that's not something that really attacts me to it. Now when it comes to ball breaks i've heard nothing but good from the ans. does anyone know exactly when/if the superbolts will be fixed so they don't break so much paint. I would do anything to not break any balls, and i'm having some bad problems will ball breaks on my stock bolt. I am now starting to lean towards the ans, considering the superbolt isn't working out.

**Nitroduck** · 01-08-2002, 09:05 PM

I hate to say this, but this is my OPINION.

Your going to have to do 2 things to get high snapshoot ROF, and break far less balls.

Either

Add a 32* foamie bolt (I know alot of people hate them, but mine works far superior to my stock AGD, same thing with my teammates RT)
Get Powerfeed
Get RT Kit
Get Intelliframe
Get Turborev

Or.......the other dreaded option

Buy a new gun.

I had Powerfeed, Intelliframe, new bolt and I still broke paint occasionally. On certain "lower grade" paints, I would break every other ball.......Because of that, I got my Angel...No regrets....But I still got my Mag which is nice for backup. But the way I play, my Mag in its current form just couldnt keep up with me or my playing style (maybe you might be different)

**strongboy2005** · 01-08-2002, 09:17 PM

thanks for the suggestion but...

see, that's totally different with me. i like to get 1 shot kills. i don't like the whole "sit there and shoot forever deal" i fire maybe 3 shots every time i snap shoot (so i prolly won't need an rt), and if i'm not fired upon after i fire that 3 shot burst then i either bunker or move. i like fast paced games. I also use only good auality paint through my mag so that wouldn't be a problem. (and i'm planning on getting a intelliframe, p/f minimag body, and i already have a very fast revvy) but i'll look into the 32 degrees bolt thanks

oh, and i prolly would get an angel if i had the choice but i can't.

SP Magic Box

SP Magic Box

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment