my girlfriends spyder rodeo is broke, i took it all apart and put it back together , no leaks everything is lubed and fine , but when i cock it and shoot it shoots only once , but it burps , i dont know what is worng with it , can sum1 please help me?
-
my ao feedback http://www.automags.org/forums/showthread.php?t=167490 -
Tank full? Sounds like low pressure. If it is, turn up the inline.SwallowBleach: It's good for you.
www.seckspb.com: for all your third party needs
Where have all the scooters gone? -BobTheCow -
Make sure there isnt to MUCH oil on the bolt. Its happened to me before. Take all the internals out, wipe them off, and oil them lightly.Comment
-
take it apart again and make sure you dident put the thick black o-ring in front of the hammer that big thick black o-ring goes BEHIND the hammer.My Gun:
Black Karta
Blue Blade Trigger
E-Mag Lowers 3.2
X-Valve
Black Dye Ultralite
Two Blue Kila V2's
Pics Coming Soon
:hail: AGD :hail:
FeedBackComment
-
just had the tank filled yesterday only shot 50 shots out of it since , its a 20oz , i did what u guys said it helped a lil but still burps but does catch and shoot fine 1 time my ao feedback http://www.automags.org/forums/showthread.php?t=167490Comment
-
Turn up the reg?
Is the sear worn?
Did it work before? I had a Spyder once with a hammer that was milled incorrectly and wouldn't reliably catch the sear.SwallowBleach: It's good for you.
www.seckspb.com: for all your third party needs
Where have all the scooters gone? -BobTheCowComment
-
Its very common to have a bad oring on the hammer/striker causing it to not recock. do you know how fast your shooting? Having to stiff of back spring versus light valve spring can effect it also. Check out the orings first 75% of the time it the problem.:hail: AGD :hail: CCI :hail:Comment
-
I would say replace the striker/hammer oring first. And are you shooting with paint? Some spyders and clones need that little bit of extra back pressure to help recock. I've had this problem on a few different spyders/clones.Comment
-
all the orings might look fine but there might be a crack in the middle of one or anything and that can cause air leakage or anything, trust me i have a shocker and yes its happened to me since theres soooo many orings
Comment
-
Cup Seal......guarenteedDub V
Where greatness is learned
and couches are burnedComment
-
no if it was the cup seal it would be pissing air down the barrel but the valve/cup seal assy could be in backwards or make sure your bolt is not in upside down make sure the hole in the bolt that the air travels thru is facing down.My Gun:
Black Karta
Blue Blade Trigger
E-Mag Lowers 3.2
X-Valve
Black Dye Ultralite
Two Blue Kila V2's
Pics Coming Soon
:hail: AGD :hail:
FeedBackComment
-
Make sure your hammer o-ring is good.
Have you tried firing it with a paintball? Some blowbacks won't operate properly without the backpressure caused by a paintball in the breech/barrel.Comment
-
this is a regular occourance on several of our spyders here....
usually casued by a bit of liquid CO2 and a humid day...
water + cold CO2 + O-rings = burps....
is your CO2 can anti-syphoned?
Comment
-
the gun workked fine , then it just stopped , it dont leak , im pretty sure everything is back together , i have been workign with it inside so theres no water or nothing, nothing is worn , its barely been used , like 5 or 6 games i think , idk im just gunna put some new parts on it or something see if it works , i hate spyders my ao feedback http://www.automags.org/forums/showthread.php?t=167490Comment
-
change the hammer o-ring.
and when you do, make sure its a hammer o-ring, not a bottle o-ring.
bottle o-rings are just slightly smaller than hammer o-rings so it'll screw it up.
[21:00] < FunkTehChillinMunky > I've got a Warped Sportz Dark TalonComment
Comment