check this out

**SpecialBlend2786** · 05-26-2005, 12:04 AM

hmmm....well that's interesting to say the least. Wonder who manufactured them. Cool stuff though. The hosing on mags is still a sore spot IMO, even if its covered in heat shrink. Too bad this isn't made anymore....

**Vex** · 05-26-2005, 01:10 AM

Kind of cool. In a very old way.

**BigEvil** · 05-26-2005, 03:34 AM

WOW I havent seen one of those in years. I believe that they were made in Europe back in the early 90's. I dont think many made it to the US.

**rkjunior303** · 05-26-2005, 07:56 AM

Wait until Muzik sees it.

**MiniSpdRcr** · 05-26-2005, 09:37 AM

Originally posted by BigEvil

WOW I havent seen one of those in years. I believe that they were made in Europe back in the early 90's. I dont think many made it to the US.

I believe that you are right sir.

**shartley** · 05-26-2005, 09:53 AM

I like the concept, but I think if it was tapped on the side (but still rear of the grip frame) and not the back it would offer a cleaner and less cluttered design.

**JimmyBeam** · 05-26-2005, 10:03 AM

very true

**SlartyBartFast** · 05-26-2005, 10:20 AM

Originally posted by shartley

I like the concept, but I think if it was tapped on the side (but still rear of the grip frame) and not the back it would offer a cleaner and less cluttered design.

Yeah. A hard line with a swivel and a disconnect. That's what I'd like to see.

How about drilling the bottom on intelli frame to accept an ASA with a top output then run a tube through the grip and along the inside of the rail and out the side. Should be able to pull off a one piece hardline from the bottom of the frame to right near the valve.

**shartley** · 05-26-2005, 10:37 AM

Originally posted by SlartyBartFast

Yeah. A hard line with a swivel and a disconnect. That's what I'd like to see.

How about drilling the bottom on intelli frame to accept an ASA with a top output then run a tube through the grip and along the inside of the rail and out the side. Should be able to pull off a one piece hardline from the bottom of the frame to right near the valve.

Yes.

**BigEvil** · 05-26-2005, 12:36 PM

The Classic RT was as close to 'hoseless' as we are going to get, and AGD still dropped the ball because you had to run and air line to the rail anyhow. I never understood why they couldnt just eliminate that completely by putting another air passage in the front of the rail and incorporating an Angel-like ASA.

GT · 05-26-2005, 12:56 PM

pretty sweet, the design is alittle to Robocop for me.

**WARPED1** · 05-26-2005, 06:51 PM

I remember seeing that gun posted here a few months ago in a thread just like this.

Cool find.

**JoshK** · 05-26-2005, 07:10 PM

It would be cool for mag owners if someone like Roguefactor, WWA, or Logic (or one of the others not mentioned) would take interest in something like this. Also, even if it has a patent...doubt it since I don't think patents last this long...someone said they never made it to the US, which means any of these companies I mentioned could make their own version of this.

**Chronobreak** · 05-26-2005, 07:14 PM

no one will buy em

the external hoses arent thaaat bad

why would people repalce theyr good frames with one that doesnt do anything mroe looks ugly and still has the same basic hose setup?

cool nontheless though

btw next time host the picture at a reputable site so we dont have to see an advertisement blcoking 80% of the image

check this out

check this out

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment