benchy owners

[FeelTheRT]

i know this has been cover in previous fourms but does anyone know a site where they show you how to make a trigger stop or make the trigger shorting on a Benchmark trigger frame? i would prefer some pictures.. u know not that i can't read *looking around nervously* i'm more of a... visual learner. thanx

[tranman]

http://members.home.com/cptung/trigmod1.htm

I haven't done it because you lose the ability to use your safety. I think www.g3pb.com has a trigger STOP mod that is much better because you can still use the safety.

[FeelTheRT]

Error 404 .

bad link.

[FeelTheRT]

hey kewl, my cuz went to MIT too.

[cphilip]

I've got some fairly good pictures of one. I will post them tomorrow for you at work. My connection is too slow here at home.

------------------
Quote: Beer is living proof that God loves us and wants us to be happy
Author: Benjamin Franklin

[FeelTheRT]

ok thanx alot.

[FeelTheRT]

any pix yet?

[cphilip]

Oh, sorry almost forgot you...

OK, I went and found these however the one showing the trigger back stop is very blurry. I know I had a decent one but haven't found it yet. I'll check my hard drive. I was cleaning up my Photopoint a few days ago and might have taken off the better one accidently. But I'll give you this one for now. And I will look for the others and email them to you?

The second pictures shows and interior set screw to push the trigger rod down. Done by Warped Sports. I don't use it at all. Too hard to set and still get the sear out. But it does work. The back stop screw is worth it though.

Just giving you the links to speed the load times for everyone else.

http://albums.photopoint.com/j/View?u=193146&a=10953897&p=45716978&Sequence=0&res=high

http://albums.photopoint.com/j/View?u=193146&a=10953897&p=45716966&Sequence=0&res=high

[cphilip]

Here's a better one showing the trigger back stop. This is an old one before I had the powder coating done to the body and the Retro valve in.

[Whisky]

Actually, i just lenghted the trigger rode so it has no back and forth slack and by doing that i can use the safe pin as a trigger stop. Ok i have no safety on the trigger but i just turn the cap on the power feed so no balls feed.
And to take the valve out i have to pull out the safety pin and pull the trigger like usual.
It works just fine for me, i have a trigger pull less than a 1/4 of an inch.


------------------
"Give me an inch... I`ll give you a bruise" -Andy Kopcok, team Image
Snap Snap
Bang Bang
You`re Out

[cphilip]

You better find a fox hole to crawl into wiskey! The trigger rod police are about to decend upon you!

[Support Mag]

Terry Garret at G3PB.com has some pics to check out. actually, if you ever get bored with your mag, go to his sit. there's usually a new picute. ive seen close to 5 incarnations through his site, and ive loved every one of em. under his projects section theres a lot to learn about a mag. check it out somtime.


------------------
Classic Mag
3" Custom Brass
12" LAPCO AutoSpirit
12 volt Revy
ANS X-Chamber
Benchmark Double Trigger Gas-Through T-Stock

[MAGBOY]

WHy did you get a bunchy? you should have waited for the new AGD frames

[cphilip]

You asking me? Well...Son...this one is two years old and green anono'd. I bought the gun used with it on there. Enough said?

[Major Ho]

Hey cphilip, we should throw a party when you hit 1000 posts. Im gonna go look around to see if anyone is up and over that mark
Woo hoo, party at ho's house

------------------
"Oh, really? I'm from Playskool. And I'm from Mattel. Actually I'm not FROM Mattel, I'm from a division of Mattel. . ." -Mr. Potato head & Rex
"Ages 3 and up. It's on my box. Ages 3 and up! I'm not supposed to be babysitting Princess Drool!" -Mr. Potato Head