latches109's emaggo

[Loguzzzzzz]

Loguzzzzzz that's awesome!! great job and thanks for the credit! Have you tried it with ramp 1 or ramp 2 yet? also what did you set your dwell to?

I should have a new frame on mine done by today. I'll try to get some video up too.

Yes I have tried the ramp modes.......

I think I may install eyes because as you know the Ego frames are capped at 15 bps unless the eyes are active. Not that 15 bps isn't enough but what the heck, if you can pull faster than that in in semi why not!!

I have not adjusted the dwell. To the best of my knowledge they are on Factory default settings.

Emaggo #1: '05 Frame, dwell 8.0

Emaggo #2; '06 Frame, dwell 10.0

Why do you ask?

I am going to buy some eyes and try to integrate them into one of these. Have you done it yet, I know you were toying with the idea.

[latches109]

Yes I have tried the ramp modes.......

I think I may install eyes because as you know the Ego frames are capped at 15 bps unless the eyes are active. Not that 15 bps isn't enough but what the heck, if you can pull faster than that in in semi why not!!

I have not adjusted the dwell. To the best of my knowledge they are on Factory default settings.

Emaggo #1: '05 Frame, dwell 8.0

Emaggo #2; '06 Frame, dwell 10.0

Why do you ask?

I am going to buy some eyes and try to integrate them into one of these. Have you done it yet, I know you were toying with the idea.

I have my dwell set around 4 ms. Just curious. I lowered the optical eye settings too.

Yea, I will be putting eyes in mine. I was looking to have elia paintball http://www.eliapaintball.com/ do this. They have experience milling shocker eyes and custom eye covers. I wanted to have shocker like eye covers that the detents would hold on.

[p8ntbal4me]

If you guys dont want to use the eyes per say,.. but want to get the stock boards out of the 15bps cap,... u can always block the eyes internally in the frame and "fool" them into
thinking they see a ball (such as the eyes on the NXT Shockers)

If they eye logic is smart like TAG's,..... you can replace the eyes with a non-photo emitter and that will cause them to see the other side all the time as well.

Personally,... I dont use eyes cause I like the twistlock bodies myself. But it I was to get into the ULE stuff,... I would have the bodies milled for eyes.

~ P8nt

[p8ntbal4me]

I bought the 2 pin leads from AKA. They were expensive $5 each plus $5 shipping. I bought 4 of them because the shipping was cheaper that way $10 shipping for multiple items.

Look HERE

I bought the first one on the list,... it was shown as "CON-2-PIN/LEADS" It didnt fit,.. too small.

So which one exactly did u use from AKA?

[olinar]

i picked up a timmy eye harness from ebay for my emaggo mod. i would link ya to one but i couldnt find one that would work. just a heads up i guess :)

[Loguzzzzzz]

I bought the first one on the list,... it was shown as "CON-2-PIN/LEADS" It didnt fit,.. too small.

So which one exactly did u use from AKA?

I used the one that you bought, I have done 4 Emaggos now and this connector has worked on each one. Do you have the stock board? Although if it was a replacement board I would think that the connector would have to work.

Don't know what to tell, you , I soldered two up last night for Emaggo #3 and #4. both have been tested too so I know that there were no issues.

I do know that they will only go in one way and it is to go into the 2 pin connector, the 4 pin is for the eyes.

Got a Pic?

[p8ntbal4me]

I used the one that you bought, I have done 4 Emaggos now and this connector has worked on each one. Do you have the stock board? Although if it was a replacement board I would think that the connector would have to work.

Don't know what to tell, you , I soldered two up last night for Emaggo #3 and #4. both have been tested too so I know that there were no issues.

I do know that they will only go in one way and it is to go into the 2 pin connector, the 4 pin is for the eyes.

Got a Pic?

I re-checked the board with the harness that AKA sent me. The connector they sent looks to be the same size as the one that works with the warp feed cable for an e-mag.

This port on the stock EGO board is larger. Im thinking the size of a pancake noid on an E2 frame,.. which would make sense since both are Eqlipse products.

[Loguzzzzzz]

I will try and get a picture posted so that you can compare them.