G-Force to release pneumatic frames for the Mags

[PhoenixWolf]

Well, it says mine's in Phoenix, so I should have it today or tomorrow. Once I get the parts together, I'll figure out what I'm gonna do with it. It should give me a much lighter alternative to my E-Mag.

[Smoothice]

Well, it says mine's in Phoenix, so I should have it today or tomorrow. Once I get the parts together, I'll figure out what I'm gonna do with it. It should give me a much lighter alternative to my E-Mag.

lighter and may be just as fast

http://www.automags.org/forums/showpost.php?p=2557233&postcount=201

[PhoenixWolf]

I never claimed to have fast fingers, but a walkable short trigger still helps me. I'll have to post a pic of the Maginov once I have it fully set up with this (green ULE Warp Mag with a stock and hopper adapter; I'll be getting a green Micro Rock for it as well). I managed to build an incredibly light, comfortable, and effective scenario marker out of it. My take on the "Mag Rifle" concept is more of an assault rifle than Noxx's setup, but honestly I think it works a LOT better.

[TwilightG]

I still haven't mounted mine to my Mag but I'm quite impressed at how light the frame is.
I know there really hasn't been much mention of it but Garf did quite a job gutting this thing!

[PhoenixWolf]

All right, I have it. And it shows I need to remove the moving mechanical arm from the sear. What is the proper way to accomplish this?

[tech-chan]

All right, I have it. And it shows I need to remove the moving mechanical arm from the sear. What is the proper way to accomplish this?

Just pull the arms of the trigger rod apart gently.

[mtaylor]

Stick a flathead screwdriver in and twist to separate the bits around the pin, and it should come off.

[PhoenixWolf]

All right. Just didn't want to bend it permanently. It sprung back, so no worries.

I've got it on the gun now, and it's as assembled as it can be until I get my LPR. I ordered the Palmers Micro Rock for it, and now just need to contact Luke to have him tap my ASA and maybe mill my rail while I'm at it. This new frame is so light it makes the gun slightly top heavy.

[babyface]

Virtue makes them. Just look. They're standard .45 grips.

thanks

[PhoenixWolf]

Ignore that. I was unaware Garth had changed the grip screw design. I will need to see if some of the 3-hole .45 grips will work for it.

[warbeak2099]

Warbeak2099,,,

My extender is a NDZ Thread Saver On/Off w/air purge.... Link to NDZ Thread Saver... I hope this helps...

WK2

It helps big time, thanks!

[Phurious]

I received my frame today; I must say the quality looks good. Thank you Garf! On a side note, does anyone know where I can get a foregrip drilled/tapped for a LPR? Anyone know of anyone selling them?

Thank you,

Phurious

[Smoothice]

pm loguzzzzzz here on ao. He can do it for you. Heck he can probably put an internal lpr in there as well if there is room.

He did an internal lpr in my chimera and it came out great.

[babyface]

i shot the frame today works great, but the barrel was sweating as if i was using co2. it was kind of humid out this morning. but couldnt understand why that was happening. any ideas?

[TwilightG]

i shot the frame today works great, but the barrel was sweating as if i was using co2. it was kind of humid out this morning. but couldnt understand why that was happening. any ideas?

Stop shooting so fast!

It happens.. my barrel tends to chill from rapid firing. Ironically, feel the valve after firing off a few good ropes of paint. It gets surprisingly warm.

There's a whole slew of physics involved that I only know a little about so I'll just leave at that.